Altera Cyclone V Device Handbook Download Page 67

Page: 67 / 1077

Related Information

•

PLLs and Clocking

on page 5-12

Provides more information about HSSI outputs.

•

LVDS Interface with External PLL Mode

on page 5-15

Provides more information about HSSI outputs.

PLL Clock Outputs

The Cyclone V PLL clock outputs can drive both GCLK and RCLK networks.

Clock Input Pin Connections to GCLK and RCLK Networks

Table 4-2: Dedicated Clock Input Pin Connectivity to the GCLK Networks for Cyclone V E, GX, and GT Devices

CLK (p/n Pins)

Clock Resources

CLK[0,1,2,3]

GCLK[0,1,2,3,4,5,6,7]

CLK[4,5,6,7]

(2)

GCLK[8,9,10,11]

CLK[8,9,10,11]

GCLK[0,1,2,3,12,13,14,15]

Table 4-3: Dedicated Clock Input Pin Connectivity to the GCLK Networks for Cyclone V SE, SX, and ST Devices

CLK (p/n Pins)

Clock Resources

CLK[0,1,2,3]

GCLK[0,1,2,3,4,5,6,7]

CLK[4,5]

(3)

GCLK[8,9,10,11]

CLK[6,7]

GCLK[0,1,2,3,12,13,14,15]

Table 4-4: Dedicated Clock Input Pin Connectivity to the RCLK Networks for Cyclone V E, GX, and GT Devices

A given clock input pin can drive two adjacent RCLK networks to create a dual-regional clock network.

CLK (p/n Pins)

Clock Resources

CLK[0]

RCLK[20,24,28,30,34,38,58,59,60,61,62,63,64,68,82,86]

CLK[1]

RCLK[21,25,29,31,35,39,58,59,60,61,62,63,65,69,83,87]

CLK[2]

RCLK[22,26,32,36,52,53,54,55,56,57,58,59,60,61,62,63,66,84]

CLK[3]

RCLK[23,27,33,37,52,53,54,55,56,57,58,59,60,61,62,63,67,85]

CLK[4]

(4)

RCLK[46,47,48,49,50,51,70,74,76,80]

CLK[5]

(4)

RCLK[46,47,48,49,50,51,71,75,77,81]

(2)

For Cyclone V E A2 and A4 devices, and Cyclone V GX C3 device, only

CLK[6]

is available.

(3)

This applies to all Cyclone V SE, SX, and ST devices except for Cyclone V SE A2 and A4 devices, and
Cyclone V SX C2 and C4 devices.

(4)

This applies to all Cyclone V E, GX, and GT devices except for Cyclone V E A2 and A4 devices, and
Cyclone V GX C3 device.

Clock Networks and PLLs in Cyclone V Devices

Altera Corporation

Send Feedback

CV-52004

PLL Clock Outputs

4-10

2014.01.10

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Cyclone V

Reviews:

Related manuals for Cyclone V

Brands by name

Popular brands

Altera Cyclone V, Device Handbook

Search results

Summary of Contents for Cyclone V

Reviews:

Related manuals for Cyclone V

Brands by name

Popular brands