Altera Cyclone V Device Handbook Download | Manualshive

Page: 74 / 1077

background image

• Down-to-up

Figure 4-15: PLL Physical Counters Orientation for Cyclone V Devices

This figure represents the top view of the silicon die that corresponds to a reverse view of the device package.

PLL

PLL

Physical Counter C0

Physical Counter C1

Physical Counter C8

Physical Counter C8

Physical Counter C7

Physical Counter C0

Physical Counter
C0 to C8
(Up-to-Down
Sequence)

Physical Counter
C8 to C0
(Down-to-Up
Sequence)

PLL Locations in Cyclone V Devices

Cyclone V devices provide a PLL for each group of three transceiver channels. These PLLs are located in a
strip, where the strip refers to an area in the FPGA.

For the PLL in the strip, only PLL counter

C[4..8]

of the strip fractional PLLs are used in a clock network.

PLL counter

C[0..3]

are used for supporting high-speed requirement of HSSI applications.

The total number of PLLs in the Cyclone V devices includes the PLLs in the PLL strip. However, the
transceivers can only use the PLLs located in the strip.

The following figures show the physical locations of the fractional PLLs. Every index represents one fractional
PLL in the device. The physical locations of the fractional PLLs correspond to the coordinates in the Quartus II
Chip Planner.

Figure 4-16: PLL Locations for Cyclone V E A2 and A4 Devices

This figure represents the top view of the silicon die that corresponds to a reverse view of the device package.

FRACTIONALPLL_X0_Y38

4

4

4

Pins

Logical Clocks

Logical Clocks

Pins

4 Logical Clocks

2 Logical Clocks

2

CLK[8..11][p,n]

CLK[0..3][p,n]

CLK[2,3]

CLK[10,11]

Pins

CLK[6][p,n]

FRACTIONALPLL_X0_Y1

FRACTIONALPLL_X54_Y1

FRACTIONALPLL_X54_Y38

3

1

Logical

Clocks

Altera Corporation

Clock Networks and PLLs in Cyclone V Devices

Send Feedback

4-17

PLL Locations in Cyclone V Devices

CV-52004
2014.01.10

«
...
72
73
74
75
76
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Brand: 3Com Pages: 20

Brand: M-Audio Pages: 10

inLab Speedcure 9494800

Brand: Dentsply Sirona Pages: 91

Brand: Genie Pages: 15

Brand: Cromemco Pages: 46

Brand: Verizon Wireless Pages: 39

Brand: T.A Pages: 11

Brand: OpenVox Pages: 13

Brand: XJTAG Pages: 9

Brand: Xilinx Pages: 8

Brand: AXAGO Pages: 2

RADEON 9800 PRO

Brand: ATI Technologies Pages: 20

crown PIP Series

Brand: Harman Pages: 16

Brand: ETAS Pages: 36

ENHANCED PSD 239 H2R

Brand: ADTRAN Pages: 2

Brand: El.Mo Pages: 16

PC/104-PCMCIA-1

Brand: Kontron Pages: 20

Brand: Lattice Semiconductor Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands