Altera Cyclone V Device Handbook Download | Manualshive

Page: 785 / 1077

background image

You can set the individual disable register (

indiv

) to disable the following interfaces between the FPGA

and HPS:

• Reset request interface
• JTAG enable interface
• I/O configuration interface
• Boundary scan interface
• Debug interface
• Trace interface
• System Trace Macrocell (STM) interface
• Cross-trigger interface (CTI)
• NAND interface
• SD/MMC interface
• SPI Master interface
• EMAC interfaces

ECC and Parity Control

The system manager can enable or disable ECC for each of the following HPS modules with ECC-protected
RAM:

• MPU L2 cache data RAM
• On-chip RAM
• USB 2.0 OTG controller (USB0 and USB1) RAM
• EMAC (EMAC0, EMAC1, and EMAC2) RAM
• DMA controller RAM
• CAN controller RAM
• NAND flash controller RAM
• Quad SPI flash controller RAM
• SD/MMC controller RAM
• DDR interfaces

The system manager can inject single-bit or double-bit errors into the MPU L2 ECC memories for testing
purposes. Set the bits in the appropriate memory enable register to inject errors. For example, to inject a
single bit EEC error, set the

injs

bit of the mpu_ctrl_l2_ecc register.

The system manager can also inject parity failures into the parity-protected RAM in the MPU L2 to test the
parity failure interrupt handler. Set the bits of the parity fail injection register (

parityinj

) to inject parity

failures.

Preloader Handoff Information

The system manager provides eight 32-bit registers to store handoff information between the preloader and
the operating system. The preloader can store any information in these registers. These register contents
have no impact on the state of the HPS hardware. When the operating system kernel boots, it retrieves the
information by reading the preloader to OS handoff information register array. These registers are reset only
by a cold reset.

Altera Corporation

System Manager

Send Feedback

14-7

ECC and Parity Control

cv_54014
2013.12.30

«
...
783
784
785
786
787
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Brand: Palo Alto Network Pages: 56

Brand: NEC Pages: 6

Brand: Omron Pages: 29

Brand: Acromag Pages: 35

Smartio CP-104UL

Brand: Moxa Technologies Pages: 2

Brand: XMOS Pages: 10

Brand: TYAN Pages: 32

Brand: MSE Pages: 35

Brand: Epson Pages: 19

Brand: Epson Pages: 2

Brand: Epson Pages: 23

Brand: Epson Pages: 35

Brand: Epson Pages: 21

Brand: Epson Pages: 49

Brand: Epson Pages: 63

Brand: Epson Pages: 98

Brand: Epson Pages: 131

Brand: Epson Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands