Altera Cyclone V Device Handbook Download Page 856 | Manualshive

Page: 856 / 1077

background image

Description

Width

In/Out

Signal Name

PHY Receive Data Valid. This signal is driven
by PHY and has multiple functions depending
on which PHY interface is selected, as listed
below:

• GMII: When high, indicates that the data

on the phy_rxd bus is valid. It remains
asserted continuously from the first
recovered byte of the frame through the final
recovered byte. Synchronous to:
phy_ clk_rx_i

• RGMII: This is the receive control signal

(RX_CTL) used to qualify the data received
on phy_rxd. On the rising edge of the clock,
rxdv is sampled. On the falling edge of the
clock, rxdv XOR rxerr is sampled.
Synchronous to: phy_clk_rx_i, both rising
and falling edges.

1

In

phy_rxdv_i

PHY Receive Error. This signal is driven by the
PHY. In GMII / MII mode, it indicates an error
or carrier extension (GMII) in the received
frame. Synchronous to: phy_clk_rx_i, This
signal is not used in RGMII mode.

1

In

phy_rxer_i

Receive clock reset output.

1

Out

rst_clk_rx_n_o

PHY Carrier Sense. This signal, valid only in
the GMII / MII mode, is asserted by the PHY
when either the transmit or receive medium is
not idle. The PHY de-asserts this signal when
both transmit and receive medium are idle. This
signal is not synchronous to any clock.

1

In

phy_crs_i

PHY Collision Detect. This signal, valid only
in GMII / MII mode operating in half duplex,
is asserted by the PHY when a collision is
detected on the medium. This signal is not
synchronous to any clock.

1

In

phy_col_i

MDIO signal input. This signal is driven
synchronously with the gmii_mdc_o clock.

1

In

gmii_mdi_i

MDIO signal data out. This signal is driven
synchronously with the gmii_mdc_o clock.

1

Out

gmii_mdo_o

MDIO signal output enable. This signal is
driven synchronously with the gmii_mdc_o
clock.

1

Out

gmii_mdo_o_e

Altera Corporation

Ethernet Media Access Controller

Send Feedback

17-7

EMAC to FPGA PHY Interface

cv_54017
2013.12.30

«
...
854
855
856
857
858
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Brand: National Instruments Pages: 162

SAFETank Series

Brand: Raidon Pages: 49

Brand: Danfoss Pages: 61

NetStructure ZT 5515

Brand: Intel Pages: 90

Brand: Falcon Pages: 24

Brand: Ruckus Wireless Pages: 56

Brand: Renesas Pages: 6

EK-FB GA AX370 Gaming RGB Monoblock

Brand: ekwb Pages: 2

Scorpio WD2500BPVT

Brand: Western Digital Pages: 3

Scorpio WD2500BPVT

Brand: Western Digital Pages: 4

Brand: NC-link Pages: 20

Brand: XJTAG Pages: 9

Brand: Xilinx Pages: 8

Brand: Active Communications Pages: 10

POD-51EH-C541U-12

Brand: IceTech Pages: 8

Brand: Intel Pages: 154

N-FXE 02B Series

Brand: Lantronix Pages: 10

CP 040 RS422/485

Brand: YASKAWA Pages: 87

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands