Altera Cyclone V Device Handbook Download Page 602 | Manualshive

Page: 602 / 1077

background image

Figure 8-1: SDRAAM Controller Subsystem High-Level Block Diagram

32-Bit AXI

Altera

PHY

Interface

Register Slave Interface

DDR
PHY

SDRAM Controller

SDRAM Controller Subsystem

64-Bit AXI

Single-Port

Controller

Multi-Port

Front End

FPGA
Fabric

AXI or

Avalon-MM

HPS

I/O

Pins

MPU

Subsystem

L3

Interconnect

FPGA-to-HPS

SDRAM Interface

32- to 256-Bit

External
Memory

L4 Peripheral Bus (osc1_clk)

Control & Status Registers

SDRAM Controller

The SDRAM controller provides high performance data access and run-time programmability. The controller
reorders data to reduce row conflicts and bus turn-around time by grouping read and write transactions
together, allowing for efficient traffic patterns and reduced latency.

The SDRAM controller consists of a multiport front end (MPFE) and a single-port controller. The MPFE
provides multiple independent interfaces to the single-port controller. The single-port controller
communicates with and manages each external memory device.

The MPFE FPGA-to-HPS SDRAM interface port has an asynchronous FIFO buffer followed by a synchronous
FIFO buffer. Both the asynchronous and synchronous FIFO buffers have a read and write data FIFO depth
of 8, and a command FIFO depth of 4. The MPU sub-system 64-bit AXI and L3 interconnect 32-bit AXI
have asynchronous FIFO buffers with read and write data FIFO depth of 8, and command FIFO depth of 4.

For more information, refer to

Memory Controller Architecture

.

DDR PHY

The DDR PHY provides a physical layer interface between the memory controller and memory devices,
which performs read and write memory operations. The DDR PHY has dataflow components, control
components, and calibration logic that handle the calibration for the SDRAM interface timing.

Related Information

Memory Controller Architecture

on page 8-4

SDRAM Controller Subsystem Interfaces

The following sections describe the SDRAM controller subsystem interfaces.

SDRAM Controller Subsystem

Altera Corporation

Send Feedback

cv_54008

SDRAM Controller Subsystem Interfaces

8-2

2013.12.30

«
...
600
601
602
603
604
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

H3C S7500E Series

Brand: H3C Pages: 34

SR8800 IM-FW-II

Brand: H3C Pages: 5

H3C S7500E Series

Brand: H3C Pages: 50

Brand: Furuno Pages: 24

OP-8000-EDFA-1U Series

Brand: Optostar Pages: 9

Brand: Softing Pages: 4

ZyXEL ZyAIR B-120

Brand: ZyXEL Communications Pages: 20

TeleCLIENT TC7730 Series

Brand: ETL Pages: 83

EK-FC980 GTX Classy

Brand: ekwb Pages: 2

Industrial Network Track OSI

Brand: GarrettCom Pages: 10

2410SA - Serial ATA RAID Controller

Brand: Adaptec Pages: 14

Brand: Xtreme Pages: 83

Brand: Cypress Semiconductor Pages: 38

Brand: Patton electronics Pages: 8

Brand: ZALMAN Pages: 12

Brand: Altera Pages: 43

Brand: Exsys Pages: 16

DVI Output Card

Brand: Extron electronics Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands