Altera Cyclone V Device Handbook Download Page 343 | Manualshive

Page: 343 / 1077

background image

Internal Clocking

This section describes the clocking architecture internal to Cyclone V transceivers.

Different physical coding sublayer (PCS) configurations and channel bonding options result in various
transceiver clock paths.

The Quartus II software automatically performs the internal clock routing based on the transceiver
configuration that you select.

Note:

The labels listed in the following table and figure mark the three sections of the transceiver internal clocking.

Table 2-2: Internal Clocking Subsections

Description

Scope

Label

Clock distribution from transmitter PLLs to channels

Transmitter Clock Network

A

Clocking architecture within transmitter channel datapath

Transmitter Clocking

B

Clocking architecture within receiver channel datapath

Receiver Clocking

C

Figure 2-5: Internal Clocking

Transmit

PLL

×1

×6

Clock Lines

×N

Transmitter

Clock

Network

Transceiver Channel

Transmitter

A

Receiver

CDR

rx_serial_data

tx_serial_data

Input

Reference Clock

Input

Reference Clock

Transceiver Channel

Transmitter

Receiver

CDR

rx_serial_data

tx_serial_data

B

C

Transmitter Clock Network

The transmitter PLL is comprised of the CMU PLL. All CMU PLLs are identical, but the usage varies
depending on channel location due to the availability of access to the clock distribution network.

Altera Corporation

Transceiver Clocking in Cyclone V Devices

Send Feedback

2-5

Internal Clocking

CV-53002
2013.05.06

«
...
341
342
343
344
345
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Brand: ZALMAN Pages: 20

Brand: Panasonic Pages: 4

UP Squared 6000 Edge Computing Kit

Brand: Aaeon Pages: 59

Brand: LaCie Pages: 4

Brand: LaCie Pages: 4

Brand: Alesis Pages: 61

Kinetic FLT 80 D5/DDC Body

Brand: EK-Quantum Pages: 16

Brand: Datasat Pages: 24

Brand: ZALMAN Pages: 11

FastTrak TX4000

Brand: Promise Technology Pages: 76

Brand: Dahua Pages: 113

Brand: S&T Pages: 28

Brand: Accusys Pages: 34

Secure Site Manager 16

Brand: Black Box Pages: 16

Brand: AMD Pages: 27

Brand: EXAGATE Pages: 7

OPTIMA II CNPS10X

Brand: ZALMAN Pages: 20

Brand: Juniper Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands