Altera Cyclone V Device Handbook Download Page 174 | Manualshive

Page: 174 / 1077

background image

Changes

Version

Date

• Removed statements about LVDS SERDES being available on top and

bottom banks only.

• Removed the topic about LVDS direct loopback mode.
• Updated the true LVDS buffers count for Cyclone V E, GX, and GT

devices.

• Added the RSKM equation, description, and high-speed timing diagram.

Updated for the Quartus II software v12.0 release:

• Restructured chapter.

2.0

June 2012

• Added “Design Considerations”, “VCCIO Restriction”, “LVDS

Channels”, “Modular I/O Banks”, and “OCT Calibration Block” sections.

• Added Figure 5–3, Figure 5–4, Figure 5–5, Figure 5–6, and Figure 5–27.
• Updated Table 5–1, Table 5–8, and Table 5–10.
• Updated Figure 5–22 with emulated LVDS with external single resistor.

• Updated Table 5–1, Table 5–2, Table 5–8, and Table 5–10.

1.2

February 2012

• Updated “I/O Banks” on page 5–8.
• Minor text edits.

• Updated Table 5–2.

1.1

November 2011

• Updated Figure 5–3, Figure 5–4.
• Updated “Sharing an OCT Calibration Block on Multiple I/O Banks”,

“High-Speed Differential I/O Interfaces”, and “Fractional PLLs and
Cyclone V Clocking” sections.

Initial release.

1.0

October 2011

Altera Corporation

I/O Features in Cyclone V Devices

Send Feedback

5-77

Document Revision History

CV-52005
2014.01.10

«
...
172
173
174
175
176
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Brand: ABB Pages: 66

Brand: Maco Pages: 38

Brand: XDS Pages: 99

F-Tile SDI II Intel Agilex

Brand: Intel Pages: 39

Brand: UfiSpace Pages: 35

Brand: Point of View Pages: 13

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

Brand: Xmart Pages: 8

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

Brand: Paradyne Pages: 6

Brand: AMX Pages: 1

Brand: ADTRAN Pages: 20

COM Express conga-TC87

Brand: Congatec Pages: 114

Total Access 1500 Dual FXS/DPO

Brand: ADTRAN Pages: 2

Brand: AMC Pages: 28

Broadband 700 MHz

Brand: Alcatel-Lucent Pages: 8

SNMP-1000-E2B1E

Brand: Advantech Pages: 4

Brand: Omron Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands