manualshive.com logo in svg

Altera Cyclone V, Device Handbook

Share
Download
Altera Cyclone V Device Handbook Download Page 267

Description

Instruction Code

JTAG Instruction

• Sets all user I/O pins to an inactive

drive state.

• Places the 1-bit bypass register

between the

TDI

and

TDO

pins.

During normal operation, the 1-bit
bypass register allows the BST data
to pass synchronously through the
selected devices to adjacent devices
while tri-stating all I/O pins until a
new JTAG instruction is executed.

• If you are testing the device after

configuration, the programmable
weak pull-up resistor or the bus
hold feature overrides the

HIGHZ

value at the pin.

00 0000 1011

HIGHZ

• Places the 1-bit bypass register

between the

TDI

and

TDO

pins.

During normal operation, the 1-bit
bypass register allows the BST data
to pass synchronously through the
selected devices to adjacent devices
while holding the I/O pins to a state
defined by the data in the
boundary-scan register.

• If you are testing the device after

configuration, the programmable
weak pull-up resistor or the bus
hold feature overrides the

CLAMP

value at the pin. The

CLAMP

value is

the value stored in the update
register of the boundary-scan cell
(BSC).

00 0000 1010

CLAMP

Emulates pulsing the

nCONFIG

pin low

to trigger reconfiguration even though
the physical pin is not affected.

00 0000 0001

PULSE_NCONFIG

Allows I/O reconfiguration (after or
during reconfigurations) through the
JTAG ports using I/O configuration
shift register (IOCSR) for JTAG testing.
You can issue the

CONFIG_IO

instruc-

tion only after the

nSTATUS

pin goes

high.

00 0000 1101

CONFIG_IO

Altera Corporation

JTAG Boundary-Scan Testing in Cyclone V Devices

Send Feedback

9-5

Supported JTAG Instruction

CV-52009
2014.01.10

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands