Altera Cyclone V Device Handbook Download Page 669 | Manualshive

Page: 669 / 1077

background image

1.

time_out

—All other interrupt bits are set to 0 when the watchdog

time_out

bit is asserted.

2.

dma_cmd_comp

—This interrupt status bit is the last to be asserted during a DMA operation to transfer

data. This bit signifies the completion of data transfer sequence.

3.

pipe_cpybck_cmd_comp

—This bit is asserted when a copyback command or the last page of a

pipeline command completes.

4.

locked_blk

—This bit is asserted when a program (or erase) is performed on a locked block.

5.

INT_act

—No relationship with other interrupt status bits. Indicates a transition from 0 to 1 on the

ready_busy

pin value for that flash device.

6.

rst_comp

—No relationship with other interrupt status bits. Occurs after a reset command has completed.

7. For an erase command:

a.

erase_fail

(if failure)

b.

erase_comp

8. For a program command:

a.

locked_blk

(if performed on a locked block)

b.

pipe_cmd_err

(if the pipeline sequence is broken by a MAP01 command)

c.

page_xfer_inc

(at the end of each page data transfer)

d.

program_fail

(if failure)

e.

pipe_cpybck_cmd_comp

f.

program_comp

g.

dma_cmd_comp

(If DMA enabled)

9. For a read command:

a.

pipe_cmd_err

(if the pipeline sequence is broken by a MAP01 command)

b.

page_xfer_inc

(at the end of each page data transfer)

c.

pipe_cpybck_cmd_comp

d.

load_comp

e.

ecc_uncor_error

(if failure)

f.

dma_cmd_comp

(If DMA enabled)

Timing Registers

You must optimize the following registers for your flash device’s speed grade and clock frequency. The
NAND flash controller operates correctly with the power-on reset values. However, functioning with
power-on reset values is a non-optimal mode that provides loose timing (large margins to the signals).

Set the following registers in the

config

group to optimize the NAND flash controller for the speed grade

of the connected device and frequency of operation of the flash controller:

•

twhr2_and_we_2_re

•

tcwaw_and_addr_2_data

•

re_2_we

•

acc_clks

•

rdwr_en_lo_cnt

•

rdwr_en_hi_cnt

•

max_rd_delay

•

cs_setup_cnt

•

re_2_re

Altera Corporation

NAND Flash Controller

Send Feedback

10-31

Timing Registers

cv_54010
2013.12.30

«
...
667
668
669
670
671
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

AllShare Cast Dongle

Brand: Samsung Pages: 2

Brand: D-Link Pages: 14

SAFETank Series

Brand: Raidon Pages: 49

MegaRAID SCSI 320-2X

Brand: LSI Pages: 4

Brand: Lancom Pages: 70

Brand: IDT Pages: 93

Brand: Longshine Pages: 27

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

Brand: IEI Technology Pages: 4

DUAL Nx56/64 1200142L1#

Brand: ADTRAN Pages: 48

Brand: WiebeTech Pages: 8

Gen3 Ethernet Module

Brand: NCD Pages: 18

Brand: ZALMAN Pages: 12

Brand: Martin Pages: 41

Brand: Cypress Semiconductor Pages: 31

Brand: Curtiss-Wright Pages: 10

Brand: KTI Networks Pages: 25

Brand: Magma Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands