Altera Cyclone V Device Handbook Download Page 479 | Manualshive

Page: 479 / 1077

background image

Clock Gating

Clock gating enables and disables clock signals.

Control and Status Registers

The clock manager contains registers used to configure and observe the clock manager.

Hardware-Managed and Software-Managed Clocks

When changing values on clocks, the terms

hardware-managed

and

software-managed

define who is

responsible for successful transitions. Software-managed clocks require that software manually gate off any
clock affected by the change, wait for any PLL lock if required, then gate the clocks back on. Hardware-
managed clocks use hardware to ensure that a glitch-free transition to a new clock value occurs. There are
three hardware-managed sets of clocks in the HPS, namely, clocks generated from the main PLL outputs
C0, C1, and C2. All other clocks in the HPS are software-managed clocks.

Clock Groups

The clock manager contains one clock group for each PLL and one clock group for the

EOSC1

pin.

OSC1 Clock Group

The clock in the OSC1 clock group is derived directly from the

EOSC1

pin. This clock is never gated or

divided.

It is used as a PLL input and also by HPS logic that does not operate on a clock output from a PLL.

Table 2-1: OSC1 Clock Group Clock

Destination

Clock Source

Frequency

Name

OSC1-driven
peripherals listed in
Table 2–9 on page 2–14

EOSC1

pin

10 to 50 MHz

osc1_clk

Main Clock Group

The main clock group consists of a PLL, dividers, and clock gating. The clocks in the main clock group are
derived from the main PLL. The main PLL is always sourced from the

EOSC1

pin of the device.

Altera Corporation

Clock Manager

Send Feedback

2-5

Clock Gating

cv_54002
2013.12.30

«
...
477
478
479
480
481
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Express5800/E120d-M

Brand: NEC Pages: 2

Brand: Data Translation Pages: 60

Brand: QSC Pages: 28

Brand: Xilica Audio Design Pages: 30

Brand: Renesas Pages: 941

Brand: SIIG Pages: 20

Brand: addlink Pages: 9

1394 Dual-Port CardBus

Brand: SIIG Pages: 8

Brand: Dataprobe Pages: 5

SinoCon C2000-C2-SHK0401-BB1

Brand: KonNad Pages: 12

UniFi WiFi BaseStation XG

Brand: Ubiquiti Pages: 19

Emotron OSTO 100

Brand: CG Pages: 112

Brand: Omron Pages: 432

Brand: ADTRAN Pages: 136

BreezeNET DS.11 Configuration Utility

Brand: Alvarion Pages: 2

com.tom INDUSTRY 100.WLAN.W

Brand: Beck Pages: 2

PC/104-PCMCIA-1

Brand: Kontron Pages: 20

cPCI-3520 Series

Brand: ADLINK Technology Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands