Altera Cyclone V Page 649 Device Handbook Download | Manualshive

Page: 649 / 1077

background image

Function

Command

Sets the destination address for the page buffer in RMW operation

0x61

Writes the page buffer for a RMW operation

0x62

Sets copy source address

0x1000

Sets copy destination address and initiates a copy of <

PP

> pages

0x11<

PP

>

Sets up a pipeline read-ahead of <

PP

> pages

0x20<

PP

>

Sets up a pipeline write of <

PP

> pages

0x21<

PP

>

MAP10 Command Usage

Use the MAP10 command as follows:

• MAP10 commands should be used to issue commands to the device, such as erase, copy-back, lock, or

unlock.

• MAP10 pipeline commands should also be used to read or write consecutive multiple pages from the

flash device within a device block boundary. The host must first issue a MAP10 pipeline read or write
command and then issue MAP01 commands to do the actual data transfers. The MAP10 pipeline read
or write command instructs the NAND flash controller to use high-performance commands such as
cache or multiplane because the flash controller has knowledge of multiple consecutive pages to be read.
The pages must not cross a block boundary. If a block boundary is crossed, the flash controller generates
an unsupported command (

unsup_cmd

) interrupt and drops the command.

• Up to four pipeline read or write commands can be issued to the NAND flash controller.
• While the NAND flash controller is performing MAP10 pipeline read or write commands, DMA must

be disabled (the

flag

bit of the

dma_enable

register in the

dma

group must be set to 0). DMA must

be disabled because the host is directly transferring data from and to the flash device through the flash
controller.

MAP11 Commands

MAP11 commands provide direct access to the NAND flash controller’s address and control cycles, allowing
software to issue the commands directly to the flash device using the

Command

and

Data

registers. The

MAP11 command is useful if the flash device supports a device-specific command not supported by standard
flash commands. It can also be useful for low-level debugging.

MAP11 commands provide a direct control path to the flash device. These commands execute command,
address, and data read/write cycles directly on the NAND device interface. Command, address, and write
data values are placed in the

Data

register. On a read, the returned data also appears in the

Data

register.

The indirect address register encodes the control operation type. Command and address cycles to the device
must be a write transaction on the host bus. For data cycles, the type of transaction on the host bus (read/write)
determines the data cycle type on the device interface. The host can issue only single-beat accesses to the
data slave port while using MAP11 commands.

Related Information

MAP11 Addressing Mapping

on page 10-12

Altera Corporation

NAND Flash Controller

Send Feedback

10-11

MAP10 Command Usage

cv_54010
2013.12.30

«
...
647
648
649
650
651
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Netlink FRX8000

Brand: Cabletron Systems Pages: 94

MMAC-Plus 9E423-24

Brand: Cabletron Systems Pages: 10

MMAC-Plus 9A128-01

Brand: Cabletron Systems Pages: 22

Spectrum EMM-E6

Brand: Cabletron Systems Pages: 2

Brand: Cabletron Systems Pages: 54

Cabletron BRIM-F6

Brand: Cabletron Systems Pages: 43

Netlink FRX4000

Brand: Cabletron Systems Pages: 60

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Pixie-4 Express

Brand: XIA Pages: 17

EK-FC780 GTX Jetstream

Brand: ekwb Pages: 2

Brand: Xilica Audio Design Pages: 30

CompactPCI CC8-BLUES

Brand: EKF Electronik Pages: 52

eBOX532-100-FL Series

Brand: AXIOMTEK Pages: 2

Brand: red lion Pages: 5

Brand: Lanner Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands