Altera Cyclone V Device Handbook Download | Manualshive

Page: 689 / 1077

background image

The internal DMA controller initiates a data transfer only when sufficient space to accommodate the
configured burst is available in the FIFO buffer or the number of bytes to the end of transfer is less than the
configured burst-length. When the DMA master interface is configured for fixed-length bursts, it transfers
data using the most efficient combination of INCR4/8/16 and SINGLE transactions. If the DMA master
interface is not configured for fixed length bursts, it transfers data using INCR (undefined length) and
SINGLE transactions.

†

Host Data Buffer Alignment

The transmit and receive data buffers in system memory must be aligned to a 32-bit boundary.

Buffer Size Calculations

The driver knows the amount of data to transmit or receive. For transmitting to the card, the internal DMA
controller transfers the exact number of bytes from the FIFO buffer, indicated by the buffer size field of the
DES1 descriptor field.

†

If a descriptor is not marked as last (with the LD bit of the DES0 field set to 0) then the corresponding
buffer(s) of the descriptor are considered full, and the amount of valid data in a buffer is accurately indicated
by its buffer size field. If a descriptor is marked as last, the buffer might or might not be full, as indicated by
the buffer size in the DES1 field. The driver is aware of the number of locations that are valid.

†

The driver

is expected to ignore the remaining, invalid bytes.

Internal DMA Controller Interrupts

Interrupts can be generated as a result of various events. The

idsts

register contains all the bits that might

cause an interrupt. The internal DMA controller interrupt enable register (

idinten

) contains an enable

bit for each of the events that can cause an interrupt to occur.

†

There are two summary interrupts—the normal interrupt summary bit (

nis

) and the abnormal interrupt

summary bit (

ais

)—in the

idsts

register.

†

The

nis

bit results from a logical OR of the transmit interrupt

(

ti

) and receive interrupt (

ri

) bits in the

idsts

register. The

ais

bit is a logical OR result of the fatal bus

error interrupt (

fbe

), descriptor unavailable interrupt (

du

), and card error summary interrupt (

ces

) bits

in the

idsts

register.

Interrupts are cleared by writing a 1 to the corresponding bit position.

†

If a 0 is written to an interrupt’s bit

position, the write is ignored, and does not clear the interrupt. When all the enabled interrupts within a
group are cleared, the corresponding summary bit is set to 0. When both the summary bits are set to 0, the
interrupt signal is de-asserted.

†

Interrupts are not queued. If another interrupt event occurs before the driver has responded to the previous
interrupt, no additional interrupts are generated. For example, the

ri

bit of the

idsts

register indicates

that one or more data has been transferred to the host buffer.

†

An interrupt is generated only once for simultaneous, multiple events. The driver must scan the

idsts

register for the interrupt cause.

†

The final interrupt signal from the controller is a logical OR of the interrupts

from the BIU and internal DMA controller.

Internal DMA Controller FSM

The following steps show the internal DMA controller finite state machine (FSM) operations:

Altera Corporation

SD/MMC Controller

Send Feedback

11-11

Host Data Buffer Alignment

cv_54011
2013.12.30

«
...
687
688
689
690
691
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

Brand: Parker Pages: 344

Brand: X-Micro Pages: 9

Brand: X-Micro Pages: 19

Brand: Yaesu Pages: 2

Converter Board R0E5212BACFG00

Brand: Renesas Pages: 6

Active Module Carrier VX402C-64

Brand: C&H Pages: 32

Brand: Daedalon Pages: 6

Brand: Cervoz Pages: 22

Quadro M6000 Sync

Brand: Nvidia Pages: 8

SiliconDrive SSD-P16G(I)-3100

Brand: Silicon Systems Pages: 108

Brand: Teletronics International Pages: 57

Brand: ACTi Pages: 12

Brand: IFM Electronic Pages: 14

Brand: B&B Electronics Pages: 17

Brand: EZCast Pages: 24

Brand: A.E.B. Pages: 28

Brand: Hologic Pages: 256

ELITE LCD UPGRADE KIT

Brand: Corsair Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands