manualshive.com logo in svg

Altera Cyclone V, Device Handbook

Share
Download
Altera Cyclone V Device Handbook Download Page 109

Mixing Voltage-Referenced and Non-Voltage Referenced I/O Standards

An I/O bank can support voltage-referenced and non-voltage-referenced pins by applying each of the rule
sets individually.

Examples:

• An I/O bank can support SSTL-18 inputs and outputs, and 1.8 V inputs and outputs with a 1.8 V V

CCIO

and a 0.9 V V

REF

.

• An I/O bank can support 1.5 V standards, 1.8 V inputs (but not outputs), and 1.5 V HSTL I/O standards

with a 1.5 V V

CCIO

and 0.75 V V

REF

.

PLLs and Clocking

The Cyclone V device family supports fractional PLLs on each side of the device. You can use fractional
PLLs to reduce the number of oscillators and the clock pins used in the FPGA by synthesizing multiple clock
frequencies from a single reference clock source.

The corner fractional PLLs can drive the LVDS receiver and driver channels. However, the clock tree network
cannot cross over to different I/O regions. For example, the top left corner fractional PLL cannot cross over
to drive the LVDS receiver and driver channels on the top right I/O bank. The Quartus II compiler
automatically checks the design and issues an error message if the guidelines are not followed.

Related Information

•

High-Speed Differential I/O Locations

on page 5-52

PLL locations that are available for each device.

•

Guideline: Use PLLs in Integer PLL Mode for LVDS

on page 5-12

Guideline: Use PLLs in Integer PLL Mode for LVDS

To drive the LVDS channels, you must use the PLLs in integer PLL mode. The corner PLLs can drive the
LVDS receiver and transmitter channels.

Guideline: Reference Clock Restriction for LVDS Application

You must use the dedicated reference clock pin of the same I/O bank used by the data channel. For I/O
banks without a dedicated reference clock pin, use the reference clock pin in the I/O bank listed in the
following table.

I/O Features in Cyclone V Devices

Altera Corporation

Send Feedback

CV-52005

Mixing Voltage-Referenced and Non-Voltage Referenced I/O Standards

5-12

2014.01.10

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands