Altera Cyclone V Device Handbook Download | Manualshive

Page: 149 / 1077

background image

Figure 5-28: LVPECL DC-Coupled Termination

Z

0

= 50 Ω

Z

0

= 50 Ω

100 Ω

LVPECL

Output Buffer

LVPECL

Input Buffer

For information about the V

ICM

specification, refer to the device datasheet.

Related Information

Cyclone V Device Datasheet

Dedicated High-Speed Circuitries

The Cyclone V device has dedicated circuitries for differential transmitter and receiver to transmit or receive
high-speed differential signals.

Table 5-34: Features and Dedicated Circuitries of the Differential Transmitter and Receiver

Differential Receiver

Differential Transmitter

Feature

LVDS, SLVS, mini-LVDS, and RSDS

LVDS, mini-LVDS, and RSDS

True differential buffer

Up to 10 bit deserializer

Up to 10 bit serializer

SERDES

Generates different phases of a clock for data
synchronizer

Clocks the load and shift
registers

Fractional PLL

—

Statically assignable

Programmable V

OD

—

Boosts output current

Programmable pre-emphasis

Inserts bit latencies into serial data

—

Data realignment block (Bit-
slip)

Manual

—

Skew adjustment

100 Ω in LVDS and SLVS standards

—

On-chip termination (OCT)

Related Information

Guideline: Use PLLs in Integer PLL Mode for LVDS

on page 5-12

High-Speed Differential I/O Locations

The following figures show the locations of the dedicated serializer/deserializer (SERDES) circuitry and the
high-speed I/Os in the Cyclone V devices.

I/O Features in Cyclone V Devices

Altera Corporation

Send Feedback

CV-52005

Dedicated High-Speed Circuitries

5-52

2014.01.10

«
...
147
148
149
150
151
...
»

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cyclone V

C50FSi - VB Network Camera

Brand: Canon Pages: 32

Brand: Rabbit Pages: 120

Brand: Campbell Pages: 42

Brand: IEI Technology Pages: 21

8677 - BladeCenter Rack-mountable - Power...

Brand: IBM Pages: 126

Brand: mikroElektronika Pages: 3

EK-Vector Radeon RX5700 + XT Backplate

Brand: ekwb Pages: 7

Brand: Aaeon Pages: 61

Brand: Quadram Pages: 21

Brand: Uctronics Pages: 12

Brand: Lanner Pages: 43

Brand: OWC Pages: 7

Brand: Panasonic Pages: 78

DVI Output Card

Brand: Extron electronics Pages: 6

Brand: Extron electronics Pages: 36

Brand: Cambium Networks Pages: 560

Brand: Dell Pages: 65

Brand: Extron electronics Pages: 220

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands