Comdial DX-80 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 352

Comdial DX-80 Скачать руководство пользователя страница 42

DX-80 I

NSTALLATION AND

M

AINTENANCE

M

ANUAL

P7290 IMM

2-12

CO Line Directory Number Matrix Per Installed Location

408M in KSU1

SLOT 1

COM4 in KSU1

SLOT 5

408E in KSU2

SLOT 1

COM4 in KSU2

SLOT 5

740,741,742,743

744,745,746,747

748,749,750,751

752,753,754,755

COM4 Installation Procedure

1. Be sure that the entire system is turned off.

2. Remove the KSU cover (four screws at each corner).

3. Connect grounded wrist strap to a suitable earth ground. (If a grounded wrist strap is not available, bleed

any static charge from your body before touching circuit modules by touching the gold-painted surface of the
inside of the KSU cabinet. If the KSU is properly grounded this will momentarily discharge static electricity
from your body.

NOTE:

A GROUNDED WRIST STRAP IS THE ONLY METHOD OF ASSURING THAT

STATIC ELECTRICITY DOES NOT DAMAGE CIRCUIT MODULES.)

4. We recommend installing the COM4 closest to the 408M/E. This means that the CPM must be temporarily

removed then repositioned above the COM4 once it is installed (in KSU1). For KSU2 installation skip step 5
and proceed with step 6.

5. Remove the installed CPM by removing the four brass standoffs used to secure the board. Retain these

standoffs for later use. Remove the ribbon cable that connects the CPM to the 408M then set aside.

6. Remove the COM4 module from the packaging and locate the four brass-color standoffs packaged with the

module.

7. Position the COM4 over the 408M/E (right-hand side) where the CPM was just removed (KSU1).

8. Use the four brass-color standoffs supplied with the COM4 to secure the COM4 in position.

408M

COM4

CPM

«
...
40
41
42
43
44
...
»

Содержание DX-80

































































































































































































































































































































































Отзывы:

Нет отзывов