manualshive.com logo in svg

Comdial DX-80, Инструкция по установке и обслуживанию, Страница: 37 / 352

Поделиться
Скачать
Comdial DX-80 Скачать руководство пользователя страница 37

DX-80 I

NSTALLATION AND 

M

AINTENANCE 

M

ANUAL

P7290 IMM

2-7

Eight Digital

Extension Ports.

KSU1: 101-108
KSU2: 125-132

Four CO Line

circuits.

KSU1: 740~743
KSU2: 748~751

J2    J3

APM4 ribbon

connector (J4)

COM4 ribbon

connector

408M: CPM ribbon cable
408E: CPM connector cable

(approximately one meter

long to extend out of KSU2

into KSU1)

Voice Processor

Power Connector

Power Failure
Transfer Port.

KSU1: 740

KSU2: 748

Extension Expansion module

connectors.

DPM8 or APM4

KSU Components

KSU1 408M and KSU2 408E

The 408M module is installed at the factory into KSU1. Although this module has the same port
configuration as the 408E, they are not interchangeable. Each 408M and 408E is equipped with 4 CO Line
Ports, 1 Power Failure Port, and 8 Digital Extension Ports. See the following diagram to locate the various
ports provided on the 408M/E.

The 408M/E is also the interface point for the various add-on modules of the DX-80 system. All peripheral

modules connect to the DX-80 via the 408M/E. See Diagram X as a reference of the various interface
connectors.

Replacing a 408 M / E

Occasionally, when instructed to do so by a Comdial technical support representative, it may be necessary to remove
a 408M or 408E and replace it in the field. Do this by following the steps below.

1.  Be sure that the entire system is turned off.

2.  Remove the KSU cover (four screws at each corner).

3.  Connect grounded wrist strap to a suitable earth ground. (If a grounded wrist strap is not available, bleed

any static charge from your body before touching circuit modules by touching the gold-painted surface of the
inside of the KSU cabinet. If the KSU is properly grounded this will momentarily discharge static electricity
from your body. 

NOTE

: A GROUNDED WRIST STRAP IS THE ONLY METHOD OF ASSURING THAT

STATIC CHARGE DOES NOT DAMAGE CIRCUIT MODULES.)

4.  Remove all circuit modules from the KSU cabinet. All modules are fastened in place using standoff

hardware. Notice: be sure that stand off placement is re-constructed when the various modules are re-

Содержание DX-80

































































































































































































































































































































































Отзывы:

Нет отзывов