Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 319 / 442

background image

THROTTLE BODIES

7-6

EAS26980

CHECKING THE INJECTORS
1. Check:

• Injectors

Damage

→

Replace.

EAS26990

CHECKING THE THROTTLE BODIES
1. Check:

• Throttle bodies

Cracks/damage

→

Replace the throttle

bodies as a set.

2. Check:

• Fuel passages

Obstructions

→

Clean.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Wash the throttle bodies in a petroleum-

based solvent.
Do not use any caustic carburetor cleaning
solution.

b. Blow out all of the passages with com-

pressed air.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS4S81001

CHECKING THE FUEL PRESSURE
1. Check:

• Fuel pressure

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the rider and passenger seat.

Refer to "GENERAL CHASSIS" on page 4-
1.

b. Disconnect the fuel hose (fuel tank to pri-

mary injector fuel rail) “1” from the primary
injector fuel rail.

WARNING

EWA4C81001

Cover fuel hose connections with a cloth
when disconnecting them. Residual pres-
sure in the fuel lines could cause fuel to
spurt out when removing the hoses.

c. Connect the pressure gauge “2” and

adapter “3” to the fuel hose (fuel tank to pri-
mary injector fuel rail).

d. Start the engine.
e. Measure the fuel pressure.

Faulty

→

Replace fuel pump.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS27030

ADJUSTING THE THROTTLE POSITION
SENSOR (FOR THROTTLE VALVES)
1. Check:

• Throttle position sensor (for throttle valves)

Refer to "CHECKING THE THROTTLE
POSITION SENSOR (FOR THROTTLE
VALVES)" on page 8-101.

2. Adjust:

• Throttle position sensor angle

Pressure gauge

90890-03153
YU-03153

Fuel pressure adapter

90890-03176
YM-03176

Fuel pressure

324 kPa (46.1 psi) (3.24 kg/

cm

2

)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
317
318
319
320
321
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Yamaha Pages: 92

Brand: CB Sabbiatrici Pages: 43

Rebellion Electric Chopper 15130760

Brand: Razor Pages: 17

Brand: DUCATI Performance Pages: 9

HIGHSIDER VICTORY

Brand: Paaschburg & Wunderlich Pages: 5

Brand: Honda Pages: 102

Brand: GAS GAS Pages: 150

Brand: kellermann Pages: 2

Brand: Hudora Pages: 8

ACCESORIES 2005

Brand: Triumph Pages: 6

Clothing Range 2006

Brand: Triumph Pages: 19

2007 ROCKET III

Brand: Triumph Pages: 20

Brand: Triumph Pages: 136

Speed Triple 1200 RS

Brand: Triumph Pages: 184

Scrambler 1200 XC

Brand: Triumph Pages: 640

Brand: Datatool Pages: 5

Brand: BMS Pages: 11

Brand: Power Fist Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands