Yamaha YZF-R1 2007 Service Manual Download

Page: 198 / 442

SWINGARM

4-69

NOTE:

Loosen the swingarm pivot shaft with the
damper rod holder (22 mm) “2”.

EAS23360

CHECKING THE SWINGARM
1. Check:

• Swingarm

Bends/cracks/damage

→

Replace.

2. Check:

• Pivot shaft

Roll the pivot shaft on a flat surface.
Bends

→

Replace.

WARNING

EWA13770

Do not attempt to straighten a bent pivot
shaft.

3. Wash:

• Pivot shaft
• Dust covers
• Spacer

• Washers
• Bearings

4. Check:

• Dust covers “1”
• Spacer “2”
• Washer “3”

Damage/wear

→

Replace.

• Bearings “4”

Damage/pitting

→

Replace.

EAS23380

INSTALLING THE SWINGARM
1. Lubricate:

• Bearings
• Spacers
• Dust covers
• Pivot shaft

2. Install:

• Bearing “1”
• Bearing “2”
• Washer “3”

Damper rod holder (22 mm)

90890-01365

Recommended cleaning solvent

Kerosene

Recommended lubricant

Molybdenum disulfide grease

Installed depth of bearing “a”

0–1.0 mm (0–0.04 in)

4. Dust cover

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands