Yamaha YZF-R1 2007 Service Manual Download

Page: 139 / 442

FRONT WHEEL

4-10

EAS21900

REMOVING THE FRONT WHEEL
1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there
is no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that
the front wheel is elevated.

2. Remove:

• Left brake caliper
• Right brake caliper

NOTE:

Do not apply the brake lever when removing
the brake calipers.

3. Elevate:

• Front wheel

NOTE:

Place the vehicle on a suitable stand so that
the front wheel is elevated.

4. Loosen:

• Front wheel axle pinch bolt

5. Remove:

• Front wheel axle bolt
• Front wheel axle
• Front wheel

EAS21920

CHECKING THE FRONT WHEEL
1. Check:

• Wheel axle

Roll the wheel axle on a flat surface.
Bends

→

Replace.

WARNING

EWA13460

Do not attempt to straighten a bent wheel
axle.

2. Check:

• Tire
• Front wheel

Damage/wear

→

Replace.

Refer to "CHECKING THE TIRES" on page
3-33 and "CHECKING THE WHEELS" on
page 3-35.

3. Measure:

• Radial wheel runout “1”
• Lateral wheel runout “2”

Over the specified limits

→

Replace.

4. Check:

• Wheel bearings

Front wheel turns roughly or is loose

→

Replace the wheel bearings.

• Oil seals

Damage/wear

→

Replace.

5. Replace:

• Wheel bearings

• Oil seals

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Clean the outside of the front wheel hub.
b. Remove the oil seals “1” with a flat-head

screwdriver.

NOTE:

To prevent damaging the wheel, place a rag “2”
between the screwdriver and the wheel sur-
face.

Radial wheel runout limit

1.0 mm (0.04 in)

Lateral wheel runout limit

0.5 mm (0.02 in)

New

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands