Yamaha YZF-R1 2007 Service Manual Download

Page: 430 / 442

ELECTRICAL COMPONENTS

8-103

b. Set the main switch to “ON”.
c. Rotate the crankshaft.
d. Measure the voltage (DC 20 V) of White/

Black and Black/Blue. With each full rota-
tion of the crankshaft, the voltage reading
should cycle from 0.8 V to 4.8 V to 0.8 V to
4.8 V.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS28410

CHECKING THE INTAKE AIR PRESSURE
SENSOR
1. Check:

• Intake air pressure sensor output voltage

Out of specification

→

Replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester (DC 20 V) to the

intake air pressure sensor coupler (wire
harness side) as shown.

b. Set the main switch to “ON”.
c. Measure the intake air pressure sensor

output voltage.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS28420

CHECKING THE INTAKE AIR TEMPERA-
TURE SENSOR
1. Remove:

• Intake air temperature sensor

(from the air filter case.)

WARNING

EWA14110

• Handle the intake air temperature sensor

with special care.

• Never subject the intake air temperature

sensor to strong shocks. If the intake air
temperature sensor is dropped, replace it.

2. Check:

• Intake air temperature sensor resistance

Out of specification

→

Replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester (

Ω

100) to the

intake air temperature sensor terminal as
shown.

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

White/Black “1”

• Negative tester probe

Black/Blue “2”

Intake air pressure sensor out-
put voltage

3.15–4.15 V

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

Pink/White “1”

• Negative tester probe

Black/Blue “2”

Intake air pressure sensor
resistance

2.21–2.69 k

Ω

at 20

C (68

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

Brown/White “1”

• Negative tester probe

Black/Blue “2”

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands