Yamaha YZF-R1 2007 Service Manual Download

Page: 425 / 442

ELECTRICAL COMPONENTS

8-98

c. Start the engine and let it run at approxi-

mately 5000 r/min.

d. Measure the charging voltage.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS28180

CHECKING THE HORN
1. Check:

• Horn resistance

Out of specification

→

Replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Disconnect the horn leads from the horn

terminals.

b. Connect the pocket tester (

Ω

1) to the

horn terminals.

c. Measure the horn resistance.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

2. Check:

• Horn sound

Faulty sound

→

Adjust or replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect a battery (12 V) to the horn.
b. Turn the adjusting screw in direction “a” or

“b” until the specified horn sound is
obtained.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS28190

CHECKING THE OIL LEVEL SWITCH
1. Drain:

• Engine oil

2. Remove:

• Oil level switch

(from the oil pan)

3. Check:

• Oil level switch resistance

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester (

Ω

100) to the

oil level switch terminal as shown.

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

Red “1”

• Negative tester probe

Black “2”

Horn resistance

1.15–1.25

Ω

at 20

C (68

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

Horn terminal “1”

• Negative tester probe

Horn terminal “2”

Oil level switch

Maximum level position resis-
tance

484–536

Ω

at 20

C (68

Minimum level position resis-
tance

114–126

Ω

at 20

C (68

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands