Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 193 / 442

background image

REAR SHOCK ABSORBER ASSEMBLY

4-64

EAS23180

HANDLING THE REAR SHOCK ABSORBER

WARNING

EWA13740

This rear shock absorber contains highly
compressed nitrogen gas. Before handling
the rear shock absorber, read and make
sure you understand the following informa-
tion. The manufacturer cannot be held
responsible for property damage or per-
sonal injury that may result from improper
handling of the rear shock absorber.
• Do not tamper or attempt to open the rear

shock absorber.

• Do not subject the rear shock absorber to

an open flame or any other source of high
heat. High heat can cause an explosion
due to excessive gas pressure.

• Do not deform or damage the rear shock

absorber in any way. Rear shock absorber
damage will result in poor damping per-
formance.

EAS23190

DISPOSING OF A REAR SHOCK
ABSORBER
1. Gas pressure must be released before dis-

posing of a rear shock absorber. To release
the gas pressure, drill a 2–3-mm hole
through the rear shock absorber at a point
15–20 mm from its end as shown.

WARNING

EWA13760

Wear eye protection to prevent eye damage
from released gas or metal chips.

EAS23230

REMOVING THE REAR SHOCK ABSORBER
ASSEMBLY
1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there
is no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that
the rear wheel is elevated.

2. Remove:

• Rear shock absorber assembly lower bolt

“1”

• Relay arm-to-swingarm bolt “2”

NOTE:

While removing the rear shock absorber
assembly lower bolt, hold the swingarm so that
it does not drop down.

3. Remove:

• Rear shock absorber upper bracket nut “1”
• Rear shock absorber assembly

NOTE:

Lower the swingarm, and the remove the rear
shock absorber assembly from between the
swingarm and frame.

EAS23240

CHECKING THE REAR SHOCK ABSORBER
ASSEMBLY
1. Check:

• Rear shock absorber rod

Bends/damage

→

Replace the rear shock

absorber assembly.

• Rear shock absorber

Gas leaks/oil leaks

→

Replace the rear

shock absorber assembly.

• Spring

Damage/wear

→

Replace the rear shock

absorber assembly.

• Bushings

Damage/wear

→

Replace.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
191
192
193
194
195
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Regal Raptor Pages: 48

Daytona 955i 2002

Brand: Triumph Pages: 384

Brand: Dakota Digital Pages: 11

Brand: BMW Pages: 88

COMP-MLCS-12200

Brand: Compcooler Pages: 11

Brand: Peugeot Motorcycles Pages: 52

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 191

Brand: Oxford Pages: 40

HotGrips OF690 Adventure

Brand: Oxford Pages: 42

PEGASO 650 TRAIL

Brand: APRILIA Pages: 12

390 Duke AR 2018

Brand: KTM Pages: 22

Brand: KTM Pages: 13

ECULMB EFI 2T ECU

Brand: GET Pages: 88

Brand: R&G Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands