Yamaha YZF-R1 2007 Service Manual Download

Page: 159 / 442

FRONT BRAKE

4-30

6. Check:

• Brake lever operation

Soft or spongy feeling

→

Bleed the brake

system.
Refer to "BLEEDING THE HYDRAULIC
BRAKE SYSTEM" on page 3-26.

EAS22490

REMOVING THE FRONT BRAKE MASTER
CYLINDER

NOTE:

Before removing the front brake master cylin-
der, drain the brake fluid from the entire brake
system.

1. Disconnect:

• Brake switch coupler “1”

(from the brake switch)

2. Remove:

• Union bolt “2”
• Copper washers “3”
• Brake hoses “4”

NOTE:

To collect any remaining brake fluid, place a
container under the master cylinder and the
end of the brake hose.

3. Remove:

• Brake master cylinder holder
• Brake master cylinder

EAS22510

CHECKING THE FRONT BRAKE MASTER
CYLINDER
1. Check:

• Brake master cylinder

Damage/scratches/wear

→

Replace.

• Brake fluid delivery passages

(brake master cylinder body)
Obstruction

→

Blow out with compressed

air.

2. Check:

• Brake master cylinder kit

Damage/scratches/wear

→

Replace.

3. Check:

• Brake fluid reservoir tank “1”

Cracks/damage

→

Replace.

• Brake fluid reservoir diaphragm “2”

Damage/wear

→

Replace.

4. Check:

• Brake hose “3”

Cracks/damage/wear

→

Replace.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands