Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 103 / 442

background image

ENGINE

3-16

4. Install:

• Air filter element

NOTE:

Install a new air filter element by fitting the pro-
jections 1 on the element into the slots in the
air filter case.

CAUTION:

ECA4C81021

• Make sure that the air filter element is

properly seated in the air filter case.

• Pay attention to handling of the products

so that the projections is not deformed.

5. Install:

• Air filter case cover

CAUTION:

ECA4C81015

Never operate the engine without the air fil-
ter element installed. Unfiltered air will
cause rapid wear of engine parts and may
damage the engine. Operating the engine
without the air filter element will also affect
throttle bodies synchronization, leading to
poor engine performance and possible
overheating.

NOTE:

When installing the air filter element into the air
filter case cover, make sure that the sealing
surfaces are aligned to prevent any air leaks.

6. Install:

• Fuel tank
• Fuel tank side covers

Refer to "FUEL TANK" on page 7-1.

• Rider seat

Refer to "GENERAL CHASSIS" on page 4-
1.

EAS21010

CHECKING THE THROTTLE BODY JOINTS
The following procedure applies to all of the
throttle body joints and intake manifolds.
1. Remove:

• Throttle bodies

Refer to "THROTTLE BODIES" on page 7-
4.

2. Check:

• Throttle body joints “1”

Cracks/damage

→

Replace.

3. Install:

• Throttle bodies

Refer to "THROTTLE BODIES" on page 7-
4.

EAS21030

CHECKING THE FUEL LINE
The following procedure applies to all of the
fuel, vacuum and breather hoses.
1. Remove:

• Rider seat

Refer to "GENERAL CHASSIS" on page 4-
1.

• Fuel tank side covers
• Fuel tank

Refer to "FUEL TANK" on page 7-1.

2. Check:

• Fuel hose “1”
• Breather hose “2”

Cracks/damage

→

Replace.

Loose connection

→

Connect properly.

1. Projection 1
2. Projection 2
3. Slot

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
101
102
103
104
105
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Caberg Pages: 3

Brand: Caberg Pages: 2

Brand: Yamaha Pages: 82

Brand: APRILIA Pages: 9

X-903 Ultra Carbon 29

Brand: X-lite Pages: 116

Brand: Gentex Pages: 15

Super Adventure 2016

Brand: KTM Pages: 25

Brand: Honda Pages: 325

Brand: R&G Pages: 6

Brand: rizoma Pages: 14

TXT ROOKIE - 2006

Brand: GAS GAS Pages: 32

Brand: Honda Pages: 123

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 8

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 6

Brand: DYNATEK Pages: 12

Brand: Triumph Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands