Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 183 / 442

background image

FRONT FORK

4-54

4. Check:

• Cap bolt O-ring “1”

Damage/wear

→

Replace.

EAS23040

ASSEMBLING THE FRONT FORK LEGS
The following procedure applies to both of the
front fork legs.

WARNING

EWA13660

• Make sure the oil levels in both front fork

legs are equal.

• Uneven oil levels can result in poor han-

dling and a loss of stability.

NOTE:

• When assembling the front fork leg, be sure

to replace the following parts:
- Outer tube bushing
- Oil seal
- Dust seal

• Before assembling the front fork leg, make

sure all of the components are clean.

1. Install:

• Damper rod assembly “1”
• Inner tube “2”
• Damper rod assembly bolt

• Cooper washer

WARNING

EWA4C81002

Always use new copper washer.

CAUTION:

ECA14210

Allow the damper rod assembly to slide
slowly down the inner tube “2” until it pro-
trudes from the bottom of the inner tube.
Be careful not to damage the inner tube.

2. Lubricate:

• Inner tube’s outer surface

3. Tighten:

• Damper rod assembly bolt “1”

NOTE:

While holding the damper rod assembly with
the damper rod holder “2”, tighten the damper
rod assembly bolt.

4. Install:

• Dust seal “1”

New

Recommended oil

Suspension oil 01 or equiva-
lent

Damper rod assembly bolt

23 Nm (2.3 m·kg, 17 ft·lb)
LOCTITE®

Damper rod holder

90890-01423

Damping rod holder

YM-01423

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
181
182
183
184
185
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Yamaha Pages: 860

Brand: Yamaha Pages: 88

B-TRK502-02-01-SL

Brand: SRC Pages: 4

EC-SIX DAYS - PART LIST 2011

Brand: GAS GAS Pages: 6

Brand: Triumph Pages: 53

Brand: Suzuki Pages: 165

Brand: Denali Pages: 5

Brand: axel joost elektronik Pages: 2

Brand: DYNATEK Pages: 4

Brand: Royal Enfield Pages: 110

Brand: BMW Pages: 205

Brand: Arai Pages: 12

Brand: Protos Pages: 6

Brand: Gemini Pages: 20

Brand: N-Com Pages: 36

Brand: Benelli Pages: 408

Brand: Petzl Pages: 10

Brand: APRILIA Pages: 264

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands