Yamaha YZF-R1 2007 Service Manual Download

Page: 194 / 442

REAR SHOCK ABSORBER ASSEMBLY

4-65

• Dust seals

Damage/wear

→

Replace.

• Bolts

Bends/damage/wear

→

Replace.

EAS23260

CHECKING THE CONNECTING ARM AND
RELAY ARM
1. Check:

• Connecting arm “1”
• Relay arm “2”

Damage/wear

→

Replace.

2. Check:

• Bearings
• Oil seals

Damage/pitting

→

Replace.

3. Check:

• Collars

Damage/scratches

→

Replace.

EAS23270

INSTALLING THE RELAY ARM
1. Lubricate:

• Collars
• Bearings

2. Install:

• Bearing “1”
• Oil seals “2”

(to the relay arm)

• Relay arm “3”
• Connecting arm “4”

EAS23310

INSTALLING THE REAR SHOCK
ABSORBER ASSEMBLY
1. Lubricate:

• Collars
• Bearings

2. Install:

• Rear shock absorber assembly

NOTE:

Install the connecting arm front bolt from the
left.

3. Tighten:

• Rear shock absorber upper bracket nut

• Rear shock absorber assembly lower nut

• Relay-arm-to-swingarm nut

Recommended lubricant

Lithium soap base grease

Installed depth “a”

1.0 mm (0.04 in)

Installed depth “b”

4.0 mm (0.16 in)

A. Left side
B. Right side

Recommended lubricant

Molybdenum disulfide grease

Rear shock absorber upper
bracket nut

92 Nm (9.2 m·kg, 67 ft·lb)

Rear shock absorber assembly
lower nut

44 Nm (4.4 m·kg, 32 ft·lb)

Relay-arm-to-swingarm nut

44 Nm (4.4 m·kg, 32 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands