Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 112 / 442

background image

CHASSIS

3-25

EAS21260

CHECKING THE REAR BRAKE PADS
The following procedure applies to all of the
brake pads.
1. Operate the brake.
2. Check:

• Rear brake pad

Wear indicators “a” almost touch the brake
disc

→

Replace the brake pads as a set.

Refer to "REAR BRAKE" on page 4-33.

EAS21280

CHECKING THE FRONT BRAKE HOSES
The following procedure applies to all of the
brake hoses and brake hose clamps.
1. Check:

• Brake hose “1”

Cracks/damage/wear

→

Replace.

2. Check:

• Brake hose clamp “2”

Loose

→

Tighten the clamp bolt.

3. Hold the vehicle upright and apply the

brake several times.

4. Check:

• Brake hose

Brake fluid leakage

→

Replace the dam-

aged hose.
Refer to "FRONT BRAKE" on page 4-20.

EAS21290

CHECKING THE REAR BRAKE HOSE
1. Check:

• Brake hose “1”

Cracks/damage/wear

→

Replace.

2. Check:

• Brake hose clamp “2”

Loose Connection

→

Tighten the clamp

bolt.

3. Hold the vehicle upright and apply the front

brake several times.

4. Check:

• Brake hose

Brake fluid leakage

→

Replace the dam-

aged hose.
Refer to "REAR BRAKE" on page 4-33.

EAS21330

ADJUSTING THE REAR BRAKE LIGHT
SWITCH

NOTE:

The rear brake light switch is operated by
movement of the brake pedal. The rear brake
light switch is properly adjusted when the
brake light comes on just before the braking
effect starts.

1. Check:

• Rear brake light operation timing

Incorrect

→

Adjust.

2. Adjust:

• Rear brake light operation timing

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
110
111
112
113
114
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Yamaha Pages: 568

B-TRK502-02-01-SL

Brand: SRC Pages: 4

COMFORT 10130810

Brand: Contracor Pages: 36

Brand: Suzuki Pages: 165

Brand: Miller Pages: 22

Brand: yasuni Pages: 9

Brand: LAS Pages: 22

Brand: dushi Pages: 4

Brand: Yamaha Pages: 400

Brand: MT Helmets Pages: 116

Brand: Honda Pages: 105

Brand: Dakota Digital Pages: 8

Dirt Track 50CC

Brand: Mash Pages: 66

Brand: Mash Pages: 69

Brand: XKGlow Pages: 2

Brand: Ohlins Pages: 8

MC 250F FACTORY EDITION 2023

Brand: GAS GAS Pages: 148

Brand: APRILIA Pages: 275

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands