Yamaha YZF-R1 2007 Service Manual Download

Page: 368 / 442

FUEL INJECTION SYSTEM

8-41

Sensor operation table

Er-4

Non-registered data has
been received from the
meter.

• Improper connection in wire harness.
• Malfunction in meter.
• Malfunction in ECU.

—

Diag-

nostic

code

No.

Item

Meter display

Checking method

Throttle position sensor (for
throttle valves) signal 1
• Fully closed position

12–21

Check with throttle valves
fully closed.

• Fully opened position

97–106

Check with throttle valves
fully opened.

Atmospheric pressure

Displays the atmospheric
pressure.

Compare the actually mea-
sured atmospheric pres-
sure with the meter display
value.

Intake air pressure

Displays intake air pressure.

Compare the actually mea-
sured atmospheric pres-
sure with the meter display
value without cranking the
engine.

Intake air temperature

Displays the intake air tem-
perature.

Compare the actually mea-
sured air temperature with
the meter display value.

Coolant temperature

Displays the coolant tempera-
ture.

Compare the actually mea-
sured coolant temperature
with the meter display
value.

Vehicle speed pulse

0–999

Check that the number
increases when the rear
wheel is rotated. The num-
ber is cumulative and does
not reset each time the
wheel is stopped.

Lean angle sensor

Remove the lean angle
sensor and incline it more
than 65 degrees.

• Upright

0.4–1.4

• Overturned

3.7–4.4

Fuel system voltage
(battery voltage)

Approximately 12.0

Set the engine stop switch
to “

”, and then compare

with the actually measured
battery voltage. (If the bat-
tery voltage is lower,
recharge the battery.)

Fault
code

No.

Symptom

Probable cause of malfunction

Diagnostic

code No.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands