Yamaha YZF-R1 2007 Service Manual Download

Page: 312 / 442

WATER PUMP

6-11

2. Install:

• Water pump seal “1”

CAUTION:

ECA14080

Never lubricate the water pump seal sur-
face with oil or grease.

NOTE:

• Install the water pump seal with the special

tools.

• Before installing the water pump seal, apply

Yamaha bond No.1215 (Three Bond
No.1215®) “2” to the water pump housing
“3”.

3. Install:

• Rubber damper holder “1”

• Rubber damper “2”

NOTE:

Before installing the rubber damper, apply tap
water or coolant onto its outer surface.

4. Measure:

• Impeller shaft tilt

Out of specification

→

Repeat steps (3)

and (4).

CAUTION:

ECA14090

Make sure the rubber damper and rubber
damper holder are flush with the impeller.

a. 17.2 mm (0.68 in)

Mechanical seal installer “4”

90890-04078

Water pump seal installer

YM-33221-A

Middle driven shaft bearing
driver “5”

90890-04058

Bearing driver 40 mm

YM-04058

Yamaha bond No. 1215 (Three
Bond No.1215®)

90890-85505

A. Push down

New

Impeller shaft tilt limit

0.15 mm (0.006 in)

1. Straightedge
2. Impeller

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands