Yamaha YZF-R1 2007 Service Manual Download

Page: 100 / 442

ENGINE

3-13

5. Drain:

• Engine oil

(completely from the crankcase)

6. If the oil filter cartridge is also to be

replaced, perform the following procedure.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the oil filter cartridge “1” with an oil

filter wrench “2”.

b. Lubricate the O-ring “3” of the new oil filter

cartridge with a thin coat of engine oil.

CAUTION:

ECA13390

Make sure the O-ring “3” is positioned cor-
rectly in the groove of the oil filter car-
tridge.

c. Tighten the new oil filter cartridge to speci-

fication with an oil filter wrench.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

7. Check:

• Engine oil drain bolt gasket

8. Install:

• Engine oil drain bolt

(along with the gasket)

9. Fill:

• Crankcase

(with the specified amount of the recom-
mended engine oil)

10. Install:

• Engine oil filler cap
• Lower cowlings

Refer to "GENERAL CHASSIS" on page 4-
1.

11. Start the engine, warm it up for several

minutes, and then turn it off.

12. Check:

• Engine

(for engine oil leaks)

13. Check:

• Engine oil level

Refer to "CHECKING THE ENGINE OIL
LEVEL" on page 3-12.

EAS20820

MEASURING THE ENGINE OIL PRESSURE
1. Check:

• Engine oil level

Below the minimum level mark ”a”

→

Add

the recommended engine oil to the proper
level.

Oil filter wrench

90890-01426
YU-38411

Oil filter cartridge

17 Nm (1.7 m·kg, 12 ft·lb)

Engine oil drain bolt

43 Nm (4.3 m·kg, 31 ft·lb)

Engine oil quantity

Total amount

3.83 L (4.05 US qt) (3.37
Imp.qt)

Without oil filter cartridge
replacement

2.90 L (3.07 US qt) (2.55
Imp.qt)

With oil filter cartridge replace-
ment

3.10 L (3.28 US qt) (2.73
Imp.qt)

New

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands