Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 122 / 442

background image

CHASSIS

3-35

WARNING

EWA14090

After extensive tests, the tires listed below
have been approved by Yamaha Motor Co.,
Ltd. for this model. The front and rear tires
should always be by the same manufac-
turer and of the same design. No guarantee
concerning handling characteristics can be
given if a tire combination other than one
approved by Yamaha is used on this vehi-
cle.

WARNING

EWA13210

New tires have a relatively low grip on the
road surface until they have been slightly
worn. Therefore, approximately 100 km
should be traveled at normal speed before
any high-speed riding is done.

NOTE:

For tires with a direction of rotation mark “1”:
• Install the tire with the mark pointing in the

direction of wheel rotation.

• Align the mark “2” with the valve installation

point.

EAS21670

CHECKING THE WHEELS
The following procedure applies to both of the
wheels.
1. Check:

• Wheel

Damage/out-of-round

→

Replace.

WARNING

EWA13260

Never attempt to make any repairs to the
wheel.

NOTE:

After a tire or wheel has been changed or
replaced, always balance the wheel.

EAS21690

CHECKING AND LUBRICATING THE
CABLES
The following procedure applies to all of the
inner and outer cables.

WARNING

EWA13270

Damaged outer cable may cause the cable
to corrode and interfere with its movement.
Replace damaged outer cable and inner
cables as soon as possible.

1. Check:

• Outer cable

Damage

→

Replace.

2. Check:

• Cable operation

Rough movement

→

Lubricate.

NOTE:

Hold the cable end upright and pour a few
drops of lubricant into the cable sheath or use
a suitable lubricating device.

EAS21700

LUBRICATING THE LEVERS
Lubricate the pivoting point and metal-to-metal
moving parts of the levers.

Front tire

Size

120/70 ZR17M/C (58W)

Manufacturer/model

MICHELIN/Pilot POWER P

Manufacturer/model

PIRELLI/DIABLO CORSA E

Rear tire

Size

190/50 ZR17M/C (73W)

Manufacturer/model

MICHELIN/ Pilot POWER

Manufacturer/model

PIRELLI/DIABLO CORSA L

Recommended lubricant

Engine oil or a suitable cable
lubricant

Recommended lubricant

Lithium-soap-based grease

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
120
121
122
123
124
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 102

SIDE FORCE 445cc

Brand: Mash Pages: 27

Saddle Tramp BC-BTHBSP

Brand: Metra Electronics Pages: 8

Brand: GAS GAS Pages: 150

Brand: BOXER Pages: 11

Brand: Free Spirits Pages: 28

HPS.08.473.10000/B

Brand: SW-Motech Pages: 4

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 8

Brand: Honeywell Pages: 93

Brand: Yamaha Pages: 64

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands