Yamaha YZF-R1 2007 Service Manual Download

Page: 202 / 442

CHAIN DRIVE

4-73

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Check:

• O-rings “1”

Damage

→

Replace the drive chain.

• Drive chain rollers “2”

Damage/wear

→

Replace the drive chain.

• Drive chain side plates “3”

Damage/wear/cracks

→

Replace the drive

chain.

5. Lubricate:

• Drive chain

6. Check:

• Drive sprocket
• Rear wheel sprocket

More than 1/4 tooth “a” wear

→

Replace

the drive chain sprockets as a set.
Bent teeth

→

Replace the drive chain

sprockets as a set.

EAS23470

CHECKING THE REAR WHEEL SPROCKET
Refer to "CHECKING AND REPLACING THE
REAR WHEEL SPROCKET" on page 4-18

EAS23480

CHECKING THE REAR WHEEL DRIVE HUB
Refer to "CHECKING THE REAR WHEEL
DRIVE HUB" on page 4-18

EAS23490

INSTALLING THE DRIVE CHAIN
1. Lubricate:

• Drive chain

2. Install:

• Drive chain “1”
• Drive sprocket “2”
• Washer
• Drive sprocket nut “3”

NOTE:

While applying the rear brake, tighten the drive
sprocket nut.

Recommended lubricant

Engine oil or chain lubricant
suitable for O-ring chains

b. Correct

1. Drive chain roller
2. Drive chain sprocket

Recommended lubricant

Engine oil or chain lubricant
suitable for O-ring chains

Drive sprocket nut

100 Nm (10 m·kg, 72 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands