Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 114 / 442

background image

CHASSIS

3-27

g. Loosen the bleed screw.

NOTE:

Loosening the bleed screw will release the
pressure and cause the brake lever to contact
the throttle grip or the brake pedal to fully
extend.

h. Tighten the bleed screw and then release

the brake lever or brake pedal.

i.

Repeat steps (e) to (h) until all of the air
bubbles have disappeared from the brake
fluid in the plastic hose.

j.

Tighten the bleed screw to specification.

k. Fill the brake fluid reservoir to the proper

level with the recommended brake fluid.
Refer to "CHECKING THE BRAKE FLUID
LEVEL" on page 3-24.

WARNING

EWA13110

After bleeding the hydraulic brake system,
check the brake operation.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS21380

ADJUSTING THE SHIFT PEDAL
1. Adjust:

• Shift pedal position

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Loosen both locknuts “1”.
b. Turn the shift rod “2” in direction “a” or “b” to

obtain the correct shift pedal position.

c. Tighten both locknuts.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS21410

ADJUSTING THE DRIVE CHAIN SLACK

NOTE:

The drive chain slack must be checked at the
tightest point on the chain.

CAUTION:

ECA13550

A drive chain that is too tight will overload
the engine and other vital parts, and one
that is too loose can skip and damage the
swingarm or cause an accident. Therefore,
keep the drive chain slack within the speci-
fied limits.

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there
is no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that
the rear wheel is elevated.

2. Spin the rear wheel several times and find

the tightest position of drive chain.

3. Check:

• Drive chain slack “a”

Out of specification

→

Adjust.

4. Adjust:

• Drive chain slack

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Loosen the wheel axle nut “1”.
b. Loosen both locknuts “2”.
c. Turn both adjusting nuts “3” in direction “a”

or “b” until the specified drive chain slack is
obtained.

Bleed screw

6 Nm (0.6 m·kg, 4.3 ft·lb)

Direction “a”

Shift pedal is raised.

Direction “b”

Shift pedal is lowered.

Drive chain slack

30.0–40.0 mm (1.18–1.57 in)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
112
113
114
115
116
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Dayi Motor Pages: 15

HUSABERG MX 2000

Brand: Ohlins Pages: 16

MILWAUKEE-EIGHT 5833

Brand: JIMS Pages: 10

Light Bee QL3000DY

Brand: Surron Pages: 18

Brand: Honda Pages: 127

Brand: Qingqi Pages: 48

Brand: Yadea Pages: 100

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 360

Brand: Yamaha Pages: 580

Brand: Yamaha Pages: 98

Brand: DYNATEK Pages: 4

Brand: Yamaha Pages: 4

Brand: Yamaha Pages: 12

Brand: Yamaha Pages: 40

Brand: Yamaha Pages: 53

Brand: Yamaha Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands