Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 106 / 442

background image

ENGINE

3-19

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

6. Install:

• EXUP valve pulley cover

7. Install:

• Lower cowlings

Refer to "GENERAL CHASSIS" on page 4-
1.

EAS28360

CHECKING THE EXUP SERVO MOTOR
1. Check:

• EXUP servo motor operation

Out of specification

→

Replace.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Check whether or not the EXUP valve is

seized.

• Disconnect the EXUP cable and check that

the EXUP valve is moved smoothly by
hand.

• When the valve is not moved smoothly,

repair or replace it.
Refer to "ADJUSTING THE EXUP
CABLES" on page 3-18.

b. When the EXUP valve is moved smoothly,

replace the EXUP servo motor.

c. Perform the self-diagnosis mode and check

the operation of EXUP valve by visual
inspection (Code No: 53).
The operation should be carried out as 3-
second drive in the full open direction, 2-
second stop and 3-second drive in the full
close direction.

d. Check that the EXUP servo motor pulley

rotates several times.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS21110

CHECKING THE COOLANT LEVEL
1. Stand the vehicle on a level surface.

NOTE:

• Place the vehicle on a suitable stand.
• Make sure the vehicle is upright.

2. Remove:

• Lower cowlings
• Right side cowling

Refer to "GENERAL CHASSIS" on page 4-
1.

3. Check:

• Coolant level

The coolant level should be between the
maximum level mark “a” and minimum level
mark “b”.
Below the minimum level mark

→

Add the

recommended coolant to the proper level.

CAUTION:

ECA13470

• Adding water instead of coolant lowers

the antifreeze content of the coolant. If
water is used instead of coolant check,
and if necessary, correct the antifreeze
concentration of the coolant.

• Use only distilled water. However, if dis-

tilled water is not available, soft water
may be used.

4. Start the engine, warm it up for several

minutes, and then turn it off.

5. Check:

• Coolant level

NOTE:

Before checking the coolant level, wait a few
minutes until it settles.

6. Install:

• Right side cowling
• Lower cowlings

Refer to "GENERAL CHASSIS" on page 4-
1.

EXUP valve pulley cover bolt

10 Nm (1.0 m·kg, 7.2 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
104
105
106
107
108
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Caberg Pages: 3

Brand: Caberg Pages: 2

Venitex BARRIER

Brand: DELTA PLUS Pages: 2

Brand: Isotta Pages: 2

Brand: MOTO GUZZI Pages: 134

VIKING 2450 Series

Brand: Lincoln Electric Pages: 48

Brand: Wunderlich Pages: 1

Brand: Wunderlich Pages: 2

Brand: Wunderlich Pages: 5

Brand: Wunderlich Pages: 5

Brand: Wunderlich Pages: 3

35832-002 BLACK

Brand: Wunderlich Pages: 8

Brand: Denali Pages: 3

Brand: Petzl Pages: 4

Brand: APRILIA Pages: 256

Brand: Polaris Pages: 2

Brand: Polaris Pages: 15

Brand: Kabuto Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands