Yamaha YZF-R1 2007 Service Manual Download

Page: 235 / 442

VALVES AND VALVE SPRINGS

5-28

3. Measure:

• Valve spring tilt “a”

Out of specification

→

Replace the valve

spring.

EAS24320

CHECKING THE VALVE LIFTERS
The following procedure applies to all of the
valve lifters.
1. Check:

• Valve lifter

Damage/scratches

→

Replace the valve

lifters and cylinder head.

EAS24340

INSTALLING THE VALVES
The following procedure applies to all of the
valves and related components.
1. Deburr:

• Valve stem end

(with an oil stone)

2. Lubricate:

• Valve stem “1”
• Valve stem seal “2”

(with the recommended lubricant)

3. Install:

• Valve “1”
• Lower spring seat “2”
• Valve stem seal “3”
• Valve spring “4”
• Upper spring seat “5”

(into the cylinder head)

NOTE:

• Make sure each valve is installed in its origi-

nal place. Refer to the following embossed
marks.
Intake valve: Pink paint mark
Exhaust valve: “4C8”

• Install the valve springs with the larger pitch

“a” facing up.

Spring tilt limit

Spring tilt (intake)

2.5

/1.7 mm

Spring tilt (exhaust)

2.5

/1.7 mm

Recommended lubricant

Molybdenum disulfide oil

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands