Yamaha YZF-R1 2007 Service Manual Download

Page: 385 / 442

FUEL INJECTION SYSTEM

8-58

Fault code No.

Symptom Lean angle sensor: open or short circuit detected.

Diagnostic code No.

Lean angle sensor

Orde
r

Item/components and probable
cause

Check or maintenance job

Reinstatement
method

Connections
• Lean angle sensor coupler
• Main wire harness ECU coupler

• Check the coupler for any pins

that may be pulled out.

• Check the locking condition of

the coupler.

• If there is a malfunction, repair it

and connect the coupler
securely.

Reinstated
automatically if
a normal signal
is received.

Open or short circuit in lead wire.

• Repair or replace if there is an

open or short circuit.

• Between lean angle sensor

coupler and ECU coupler.
(Blue–Blue)
(Yellow/Green–Yellow/Green)
(Black/Blue–Black/Blue)

Defective lean angle sensor.

• Execute the diagnostic mode.

(Code No.08)

• Replace if defective.

Refer to "CHECKING THE
LEAN ANGLE SENSOR" on
page 8-96.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands