Yamaha YZF-R1 2007 Service Manual Download

Page: 330 / 442

IGNITION SYSTEM

8-3

EAS27150

TROUBLESHOOTING
The ignition system fails to operate (no spark or intermittent spark).

NOTE:

• Before troubleshooting, remove the following part(s):
1 Rider seat
2 Passenger seat
3 Fuel tank
4 Side cowlings

→

↓

→

↓

→

↓

→

↓

→

↓

→

↓

→

↓

1 Check the fuses.

(Main and ignition)
Refer to "CHECKING THE FUSES"
on page 8-89.

Replace the fuse(s).

2 Check the battery.

Refer to "CHECKING AND
CHARGING THE BATTERY" on
page 8-89.

• Clean the battery terminals.
• Recharge or replace the battery.

3 Check the spark plugs.

Refer to "CHECKING THE SPARK
PLUGS" on page 3-10.

Re-gap or replace the spark plugs.

4 Check the ignition spark gap.

Refer to "CHECKING THE IGNI-
TION COILS" on page 8-95.

Ignition system is OK.

5 Check the ignition coils.

Refer to "CHECKING THE IGNI-
TION COILS" on page 8-95.

Replace the ignition coils.

6 Check the crankshaft position sen-

sor.
Refer to "CHECKING THE
CRANKSHAFT POSITION SEN-
SOR" on page 8-96.

Replace the crankshaft position sen-
sor.

7 Check the main switch.

Refer to "CHECKING THE
SWITCHES" on page 8-85.

Replace the main switch/immobilizer
unit assembly.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands