Yamaha YZF-R1 2007 Service Manual Download

Page: 421 / 442

ELECTRICAL COMPONENTS

8-94

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester (DC 20 V) to the

turn signal/hazard relay terminal as shown.

b. Turn the main switch to “ON”.
c. Measure the turn signal/hazard relay out-

put voltage.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS28050

CHECKING THE RELAY UNIT (DIODE)
1. Check:

• Relay unit (diode)

Out of specification

→

Replace.

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

• Positive tester probe

→

Brown/White “1”

• Negative tester probe

→

Ground

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

Continuity

Positive tester probe

→

Sky

blue “1”
Negative tester probe

→

Black/Yellow “2”

No continuity

Positive tester probe

→

Black/

Yellow “2”
Negative tester probe

→

Sky

blue “1”

Continuity

Positive tester probe

→

Sky

blue “1”
Negative tester probe

→

Blue/

Yellow “3”

No continuity

Positive tester probe

→

Blue/

Yellow “3”
Negative tester probe

→

Sky

blue “1”

Continuity

Positive tester probe

→

Sky

blue “1”
Negative tester probe

→

Sky

blue/White “4”

No continuity

Positive tester probe

→

Sky

blue/White “4”
Negative tester probe

→

Sky

blue “1”

Continuity

Positive tester probe

→

Blue/

Black “5”
Negative tester probe

→

Blue/

Yellow “3”

No continuity

Positive tester probe

→

Blue/

Yellow “3”
Negative tester probe

→

Blue/

Black “5”

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands