Yamaha YZF-R1 2007 Service Manual Download

Page: 181 / 442

FRONT FORK

4-52

EAS22970

REMOVING THE FRONT FORK LEGS
The following procedure applies to both of the
front fork legs.
1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there
is no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that
the front wheel is elevated.

2. Remove:

• Front wheel

Refer to "FRONT WHEEL" on page 4-8.

• Front brake caliper

Refer to "FRONT BRAKE" on page 4-20.

• Side cowlings

Refer to "GENERAL CHASSIS" on page 4-
1.

3. Loosen:

• Handlebar pinch bolt “1”
• Upper bracket pinch bolts “2”
• Cap bolt “3”
• Lower bracket pinch bolts “4”

WARNING

EWA13640

Before loosening the upper and lower
bracket pinch bolts, support the front fork
leg.

4. Remove:

• Front fork leg

EAS22990

DISASSEMBLING THE FRONT FORK LEGS
The following procedure applies to both of the
front fork legs.
1. Remove:

• Cap bolt “1”

(from the damper adjusting rod)

• Spacers “2”
• Nut “3”

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Press down on the spacer with the fork

spring compressor “4”.

b. Install the rod holder “5” between the nut

“3” and the spacer “2”.

NOTE:

Use the side of the rod holder that is marked
“A”.

c. Hold the spring preload adjusting bolt “6”

and loosen the nut “3”.

d. Remove the cap bolt.
e. Remove the rod holder and fork spring

compressor.

Remove the spacer and nut.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

2. Drain:

• Fork oil

NOTE:

Stroke the damper rod “1” several times while
draining the fork oil.

Fork spring compressor

90890-01441
YM-01441

Rod holder

90890-01434

Damper rod holder double
ended

YM-01434

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands