Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 99 / 442

background image

ENGINE

3-12

8. Connect:

• Ignition coils

EAS20730

CHECKING THE ENGINE OIL LEVEL
1. Stand the vehicle on a level surface.

NOTE:

• Place the vehicle on a suitable stand.
• Make sure the vehicle is upright.

2. Start the engine, warm it up for several

minutes, and then turn it off.

3. Check:

• Engine oil level

The engine oil level should be between the
minimum level mark “a” and maximum level
mark “b”.
Below the minimum level mark

→

Add the

recommended engine oil to the proper
level.

CAUTION:

ECA13360

• Engine oil also lubricates the clutch and

the wrong oil types or additives could

cause clutch slippage. Therefore, do not
add any chemical additives or use engine
oils with a grade of CD “a” or higher and
do not use oils labeled “ENERGY CON-
SERVING II” “b”.

• Do not allow foreign materials to enter the

crankcase.

4. Start the engine, warm it up for several

minutes, and then turn it off.

5. Check the engine oil level again.

NOTE:

Before checking the engine oil level, wait a few
minutes until the oil has settled.

EAS20790

CHANGING THE ENGINE OIL
1. Start the engine, warm it up for several

minutes, and then turn it off.

2. Place a container under the engine oil drain

bolt.

3. Remove:

• Lower cowlings

Refer to "GENERAL CHASSIS" on page 4-
1.

4. Remove:

• Engine oil filler cap “1”
• Engine oil drain bolt “2”

(along with the gasket)

Type

SAE10W30, SAE10W40,
SAE15W40, SAE20W40 or
SAE20W50

Recommended engine oil grade

API service, SG type or higher,
JASO standard MA

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
97
98
99
100
101
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Nolan Pages: 24

HUSABERG MX 2000

Brand: Ohlins Pages: 16

Brand: National Cycle Pages: 5

SPORTTOURING ST4S

Brand: Ducati Pages: 313

Brand: Shark Pages: 80

Brand: Arai Helmet Pages: 28

Brand: Yamaha Pages: 34

Brand: Yamaha Pages: 34

Brand: Yamaha Pages: 53

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 112

Brand: Yamaha Pages: 122

Brand: Yamaha Pages: 126

XMAX CZD300M 2021

Brand: Yamaha Pages: 126

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 215

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands