manualshive.com logo in svg

Yamaha YZF-R1 2007, Service Manual

The Yamaha YZF-R1 2007 Service Manual is a comprehensive guide for motorcycle enthusiasts. This manual provides detailed instructions and essential information to service, repair, and maintain the Yamaha YZF-R1 2007 model. Download this valuable resource for free from manualshive.com, your go-to destination for user manuals.

Share
Download
background image

VALVES AND VALVE SPRINGS

5-24

1. Measure:

• Valve-stem-to-valve-guide clearance

Out of specification 

→

 Replace the valve 

guide.

2. Replace:

• Valve guide

NOTE:

To ease valve guide removal and installation, 
and to maintain the correct fit, heat the cylinder 
head to 100

°

C (212

°

F) in an oven.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the valve guide with the valve 

guide remover “1”.

b. Install the new valve guide with the valve 

guide installer “2” and valve guide remover 
“1”.

c. After installing the valve guide, bore the 

valve guide with the valve guide reamer “3” 
to obtain the proper valve-stem-to-valve-
guide clearance.

NOTE:

After replacing the valve guide, reface the 
valve seat.

• Valve-stem-to-valve-guide clearance =

Valve guide inside diameter “a” -
Valve stem diameter “b”

Valve-stem-to-valve-guide clear-
ance

Valve-stem-to-valve-guide clear-
ance (intake)

0.010–0.037 mm (0.0004–
0.0015 in)

Limit

0.080 mm (0.0032 in)

Valve-stem-to-valve-guide clear-
ance (exhaust)

0.025–0.052 mm (0.0010–
0.0020 in)

Limit

0.100 mm (0.0039 in)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Keis X900 Operating Instructions preview
X900
Brand: Keis Pages: 2
Öhlins YA812 Mounting Instructions preview
YA812
Brand: Öhlins Pages: 2
Öhlins YA 314 Mounting Instructions preview
YA 314
Brand: Öhlins Pages: 2
Öhlins TR 538 Mounting Instructions preview
TR 538
Brand: Öhlins Pages: 2
Öhlins ST44 Mounting Instructions preview
ST44
Brand: Öhlins Pages: 2
Öhlins SD195 Mounting Instruction preview
SD195
Brand: Öhlins Pages: 2
Öhlins SD 168 Mounting Instructions preview
SD 168
Brand: Öhlins Pages: 2
Öhlins SD 154 Mounting Instructions preview
SD 154
Brand: Öhlins Pages: 2
Öhlins RS 562 Mounting Instructions preview
RS 562
Brand: Öhlins Pages: 2
Öhlins POF5H00 Mounting Instructions preview
POF5H00
Brand: Öhlins Pages: 2
Yamaha PW50M2 Owner'S Manual preview
PW50M2
Brand: Yamaha Pages: 82
Suzuki GS500E Service Manual preview
GS500E
Brand: Suzuki Pages: 440
Malossi CDI Manual preview
CDI
Brand: Malossi Pages: 36
LSL 121B029 Fitting Instruction preview
121B029
Brand: LSL Pages: 12
DYNATEK DDK2-16 Installation Instructions Manual preview
DDK2-16
Brand: DYNATEK Pages: 7
DYNATEK DDK3-4 Installation Manual preview
DDK3-4
Brand: DYNATEK Pages: 12
hepco & becker 630209 Assembling Instructions preview
630209
Brand: hepco & becker Pages: 6
Ops-Core FAST SF Operating Manual preview
FAST SF
Brand: Ops-Core Pages: 20

Brands by name

Popular brands

Load more brands