Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 97 / 442

background image

ENGINE

3-10

c. Tighten the locknut “1”.

WARNING

EWA4C81006

After adjusting the throttle cable free play,
start the engine and turn the handlebars to
the right and to the left to ensure that this
does not cause the engine idling speed to
change.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS20680

CHECKING THE SPARK PLUGS
The following procedure applies to all of the
spark plugs.
1. Remove:

• Side cowlings
• Lower cowlings

Refer to "GENERAL CHASSIS" on page 4-
1.

2. Remove:

• Radiator upper bolts
• Radiator lower bolt

Refer to "RADIATOR" on page 6-1.

3. Disconnect:

• Ignition coils

4. Remove:

• Spark plugs

CAUTION:

ECA13320

Before removing the spark plugs, blow
away any dirt accumulated in the spark
plug wells with compressed air to prevent it
from falling into the cylinders.

5. Check:

• Spark plug type

Incorrect

→

Change.

6. Check:

• Electrode “1”

Damage/wear

→

Replace the spark plug.

• Insulator “2”

Abnormal color

→

Replace the spark plug.

Normal color is medium-to-light tan.

7. Clean:

• Spark plugs

(with a spark plug cleaner or wire brush)

8. Measure:

• Spark plug gap “a”

(with a wire thickness gauge)
Out of specification

→

Regap.

9. Install:

• Spark plugs
• Ignition coils

NOTE:

Before installing the spark plug, clean the
spark plug and gasket surface.

10. Install:

• Radiator upper bolts
• Radiator lower bolt

Refer to "RADIATOR" on page 6-1.

11. Install:

• Side cowlings
• Lower cowlings

Refer to "GENERAL CHASSIS" on page 4-
1.

Direction “a”

Throttle cable free play is increased.

Direction “b”

Throttle cable free play is decreased.

Manufacturer/model

NGK/CR9EK

Spark plug gap

0.6–0.7 mm (0.024–0.028 in)

Spark plug

13 Nm (1.3 m·kg, 9.4 ft·lb)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
95
96
97
98
99
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Dakota Digital Pages: 38

Brand: Yamaha Pages: 102

Brand: N-Com Pages: 36

DaVinci RSV4-APRC

Brand: STARLANE Pages: 2

Freeride 350 2013

Brand: KTM Pages: 113

Brand: Miller Pages: 22

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 216

Brand: Yamaha Pages: 380

Brand: Yamaha Pages: 658

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands