Yamaha YZF-R1 2007 Service Manual Download

Page: 120 / 442

CHASSIS

3-33

Compression damping (fast compression
damping)

CAUTION:

ECA13590

Never go beyond the maximum or minimum
adjustment positions.

1. Adjust:

• Compression damping (fast compression

damping)

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Turn the adjusting screw “1” in direction “a”

or “b”.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Compression damping (slow compression
damping)

CAUTION:

ECA13590

Never go beyond the maximum or minimum
adjustment positions.

1. Adjust:

• Compression damping (slow compression

damping)

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Turn the adjusting knob “1” in direction “a”

or “b”.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS21650

CHECKING THE TIRES
The following procedure applies to both of the
tires.
1. Check:

• Tire pressure

Out of specification

→

Regulate.

Direction “a”

Compression damping is increased
(suspension is harder).

Direction “b”

Compression damping is decreased
(suspension is softer).

Compression damping (fast com-
pression damping) adjusting
positions

Minimum

4 turn(s) out*

Standard

3 turn(s) out*

Maximum

0 turn(s) out*

* With the adjusting screw fully turned in.

Direction “a”

Compression damping is increased
(suspension is harder).

Direction “b”

Compression damping is decreased
(suspension is softer).

Compression damping (slow
compression damping) adjusting
positions

Minimum

20 click(s) out*

Standard

12 click(s) out*

Maximum

1 click(s) out*

* With the adjusting screw fully turned in.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands