Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 365 / 442

background image

FUEL INJECTION SYSTEM

8-38

NOTE:

If the engine stop switch is set to “

”, set it to “

”, and then set it to “

” again.

9. Turn the main switch to “OFF” to cancel the diagnostic mode.

Fault code table

Fault
code

No.

Symptom

Probable cause of malfunction

Diagnostic

code No.

11

No normal signals are
received from the cylinder
identification sensor when
the engine is started or
while the vehicle is being
driven.

• Open or short circuit in sub-wire-harness 1.
• Open or short circuit in wire harness.
• Defective cylinder identification sensor.
• Malfunction in ECU.
• Improperly installed sensor.

—

12

No normal signals are
received from the crank-
shaft position sensor.

• Open or short circuit in wire harness.
• Defective crankshaft position sensor.
• Malfunction in pickup rotor.
• Malfunction in ECU.
• Improperly installed sensor.

—

13

Intake air pressure sensor:
open or short circuit
detected.

• Open or short circuit in wire harness.
• Defective intake air pressure sensor.
• Malfunction in ECU.

03

14

Intake air pressure sensor:
hose system malfunction
(clogged or detached
hose).

• Intake air pressure sensor hose is

detached, clogged, kinked, or pinched.

• Malfunction in ECU.

03

15

Throttle position sensor (for
throttle valves): open or
short circuit detected.
Throttle position sensor (for
throttle valves) coupler con-
nection is loose.

• Open or short circuit in wire harness.
• Defective throttle position sensor (for throt-

tle valves).

• Malfunction in ECU.
• Improperly installed throttle position sensor

(for throttle valves).

01
13

17

EXUP servo motor circuit:
open or short circuit
detected or loose connec-
tion.

• Open or short circuit in wire harness.
• Defective EXUP servo motor (potentiometer

circuit).

53

18

EXUP servo motor is stuck.

• Open or short circuit in wire harness.
• Stuck EXUP servo motor (mechanism).
• Stuck EXUP servo motor (motor).

53

19

Open circuit is detected in
the input lead from the side-
stand switch to the ECU.

• Open circuit in wire harness (ECU Coupler).
• Malfunction in ECU.
• Relay unit (diode)

20

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
363
364
365
366
367
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: GAS GAS Pages: 142

Brand: Suzuki Pages: 59

STEADYSTAND Cross Basic

Brand: ACEBIKES Pages: 6

Brand: Ohlins Pages: 8

Brand: AGV Pages: 45

Brand: LAZER Pages: 11

Stealth Air Cleaner Kit

Brand: S&S Cycle Pages: 4

Brand: Ducati Pages: 77

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 96

Brand: Honeywell Pages: 8

Brand: Honeywell Pages: 304

Brand: Happy Trails Pages: 2

Brand: Yamaha Pages: 9

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands