Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 214 / 442

background image

ENGINE REMOVAL

5-7

EAS23720

INSTALLING THE ENGINE
1. Install:

• Engine mounting adjust bolts

(temporary tighten)

2. Install:

• Engine

3. Install:

• Engine mounting bolt (rear lower side) “1”
• Engine mounting bolt (rear upper side) “2”
• Locknuts

NOTE:

Lubricate the lower and upper engine mount-
ing bolts threads with lithium-soap-based
grease.

4. Install:

• Engine mount bolt (front left side) “1”

(temporary tighten)

5. Install:

• Engine mount collar (inner) “1”
• Engine mount collar (center) “2”
• Engine mount collar (outer) “3”
• Right front engine mount bolt “4”

(temporary tighten)

6. Tighten:

• Engine mounting adjust bolts

NOTE:

Use the pivot shaft wrench “1” and pivot shaft
wrench adapter “2” to tighten the engine
mounting adjust bolts.

7. Tighten:

• Upper locknut “1”
• Lower locknut “2”

Engine mounting adjust bolt

7 Nm (0.7 m·kg, 5.1 ft·lb)

Pivot shaft wrench

90890-01471
YM-01471

Pivot shaft wrench adapter

90890-01476

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
212
213
214
215
216
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: Palm Pages: 14

Brand: R&G Pages: 3

Brand: Ecomobility Green World Pages: 24

Brand: Dräger Pages: 256

F12R AIR 50 cc. - Euro 2

Brand: Malaguti Pages: 46

Brand: RIEJU Pages: 34

Brand: Baotian Pages: 30

BOOMERANG 7554CB

Brand: Bagster Pages: 2

Brand: Benelli Pages: 314

Brand: KTM Pages: 7

Brand: COLORADO Pages: 21

Rungu Dualie Rugged Series

Brand: Standard Bearer Machines Pages: 106

Brand: Gmax Pages: 26

Pulsar 150 CC DTS-i

Brand: Bajaj Pages: 16

TRAMP TOUR BOX LCK5093

Brand: lehman Trikes Pages: 12

Brand: Xmotos Pages: 79

Brand: rizoma Pages: 12

Brand: OKAI Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands