Yamaha YZF-R1 2007 Service Manual Download

Page: 306 / 442

OIL COOLER

6-5

EAS26420

CHECKING THE OIL COOLER
1. Check:

• Oil cooler

Cracks/damage

→

Replace.

2. Check:

• Oil cooler inlet hose
• Oil cooler outlet hose

Cracks/damage/wear

→

Replace.

EAS26430

INSTALLING THE OIL COOLER
1. Clean:

• Mating surfaces of the oil cooler and the

crankcase
(with a cloth dampened with lacquer thin-
ner)

2. Install:

• O-ring
• Oil cooler “1”

• Washer “2”
• Oil cooler bolt “3”

NOTE:

• Before installing the oil cooler, lubricate the

oil cooler bolt and O-ring with a thin coat of
engine oil.

• Make sure the O-ring is positioned properly.
• Align the projection “a” on the oil cooler with

the slot “b” in the crankcase.

3. Fill:

• Cooling system

(with the specified amount of the recom-
mended coolant)
Refer to "CHANGING THE COOLANT" on
page 3-20.

• Crankcase

(with the specified amount of the recom-
mended engine oil)
Refer to "CHANGING THE ENGINE OIL"
on page 3-12.

4. Check:

• Cooling system

Leaks

→

Repair or replace any faulty part.

Oil cooler

63 Nm (6.3 m·kg, 46 ft·lb)

New

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands