Yamaha YZF-R1 2007 Service Manual Download

Page: 158 / 442

FRONT BRAKE

4-29

• Whenever a brake caliper is disassem-

bled, replace the brake caliper piston
seals.

EAS22450

INSTALLING THE FRONT BRAKE CALI-
PERS
The following procedure applies to both of the
brake calipers.
1. Install:

• Brake pads
• Brake pad springs
• Brake pad pins

2. Install:

• Brake caliper “1”

• Copper washers
• Brake hose “2”
• Union bolt “3”
• Brake hose holder

WARNING

EWA13530

Proper brake hose routing is essential to
insure safe vehicle operation. Refer to
"CABLE ROUTING" on page 2-39.

CAUTION:

ECA14170

When installing the brake hose onto the
brake caliper “1”, make sure the brake pipe
“a” touches the projection “b” on the brake
caliper.

3. Fill:

• Brake fluid reservoir

(with the specified amount of the recom-
mended brake fluid)

WARNING

EWA13090

• Use only the designated brake fluid.

Other brake fluids may cause the rubber
seals to deteriorate, causing leakage and
poor brake performance.

• Refill with the same type of brake fluid

that is already in the system. Mixing brake
fluids may result in a harmful chemical
reaction, leading to poor brake perfor-
mance.

• When refilling, be careful that water does

not enter the brake fluid reservoir. Water
will significantly lower the boiling point of
the brake fluid and could cause vapor
lock.

CAUTION:

ECA13540

Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.

4. Bleed:

• Brake system

Refer to "BLEEDING THE HYDRAULIC
BRAKE SYSTEM" on page 3-26.

5. Check:

• Brake fluid level

Below the minimum level mark “a”

→

Add

the recommended brake fluid to the proper
level.
Refer to "CHECKING THE BRAKE FLUID
LEVEL" on page 3-24.

Recommended fluid

DOT 4

Front brake caliper bolt

35 Nm (3.5 m·kg, 25 ft·lb)

Front brake hose union bolt

30 Nm (3.0 m·kg, 22 ft·lb)

Front brake hose holder

6 Nm (0.6 m·kg, 4.3 ft·lb)

New

Recommended fluid

DOT 4

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands