Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 17 / 442

background image

FEATURES

1-8

EAS4C81024

INSTRUMENT FUNCTIONS

Multi-function meter unit

WARNING

EWA4C81008

Be sure to stop the vehicle before making
any setting changes to the multi-function
meter unit.

The multi-function meter unit is equipped with
the following:
• a speedometer (which shows the riding

speed)

• a tachometer (which shows engine speed)
• an odometer (which shows the total distance

traveled)

• two tripmeters (which show the distance trav-

eled since they were last set to zero)

• a fuel reserve tripmeter (which shows the

distance traveled since the fuel level warning
light came on)

• a clock
• a coolant temperature display
• an air intake temperature display
• a self-diagnosis device
• a display brightness and shift timing indicator

light control mode

NOTE:

• Be sure to turn the key to “ON” before using

the “SELECT” and “RESET” buttons.

• For the U.K. only: To switch the speedometer

and odometer/tripmeter displays between

kilometers and miles, press the “SELECT”
button for at least one second.

Tachometer

The electric tachometer allows the rider to
monitor the engine speed and keep it within
the ideal power range.
When the key is turned to “ON”, the tachome-
ter needle will sweep once across the r/min
range and then return to zero r/min in order to
test the electrical circuit.

CAUTION:

ECA4C81017

Do not operate the engine in the tachome-
ter red zone.
Red zone: 13750 r/min and above

Clock mode

Turn the key to “ON”.
To set the clock
1. Push the “SELECT” button and “RESET”

button together for at least two seconds.

2. When the hour digits start flashing, push

the “RESET” button to set the hours.

3. Push the “SELECT” button, and the minute

digits will start flashing.

4. Push the “RESET” button to set the minutes.

1. Clock
2. Speedometer
3. “SELECT” button
4. “RESET” button
5. Tachometer
6. Coolant temperature display/air intake tem-

perature display

7. Odometer/tripmeters/fuel reserve tripme-

ter/ stopwatch

8. Shift timing indicator light

1. Tachometer
2. Tachometer red zone

1. Clock

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

«
...
15
16
17
18
19
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Zero S Series 2014

Brand: Zero Motorcycles Pages: 128

Freeride E-XC 2019

Brand: KTM Pages: 44

Brand: Ducati Pages: 123

Brand: SUR-RON Pages: 50

Brand: MadStad Engineering Pages: 8

Brand: R&G Pages: 9

Brand: Suzuki Pages: 526

Grizzly Minicross RCX/12 50CC

Brand: Malaguti Pages: 33

Brand: hepco & becker Pages: 7

Brand: SHERCO Pages: 102

Brand: Yamaha Pages: 215

Brand: Yamaha Pages: 319

Brand: Yamaha Pages: 688

XMAX YP250R 2013

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 112

Brand: R&G Pages: 6

Brand: APRILIA Pages: 235

Brand: MARTINDALE Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands