Yamaha YZF-R1 2007 Service Manual Download

Page: 118 / 442

CHASSIS

3-31

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Rebound damping

CAUTION:

ECA13590

Never go beyond the maximum or minimum
adjustment positions.

1. Adjust:

• Rebound damping

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Turn the adjusting screw “1” in direction “a”

or “b”.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Compression damping

CAUTION:

ECA13590

Never go beyond the maximum or minimum
adjustment positions.

1. Adjust:

• Compression damping

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Turn the adjusting screw “1” in direction “a”

or “b”.

Spring preload adjusting posi-
tions

Minimum

Standard

Maximum

Direction “a”

Rebound damping is increased
(suspension is harder).

Direction “b”

Rebound damping is decreased
(suspension is softer).

Rebound damping adjust posi-
tions

Minimum

26 click(s) out*

Standard

10 click(s) out*

Maximum

1 click(s) out*

* With the adjusting screw fully turned in.

Direction “a”

Compression damping is increased
(suspension is harder).

Direction “b”

Compression damping is decreased
(suspension is softer).

Compression damping adjust
points

Minimum

25 click(s) out*

Standard

10 click(s) out*

Maximum

1 click(s) out*

* With the adjusting screw fully turned in.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands