Yamaha YZF-R1 2007 Service Manual Download

Page: 286 / 442

CRANKSHAFT

5-79

11. Install:

• Cylinder assembly “1”
• Connecting rod caps “2”

NOTE:

• Make sure that the “Y” marks “a” on the con-

necting rods face towards the left side of the
crankshaft.

• Make sure that the characters on both the

connecting rod and connecting rod cap are
aligned.

12. Tighten:

• Connecting rod bolts

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

CAUTION:

ECA14980

Tighten the connecting rod bolts using the
plastic-region tightening angle method.

a. Clean the connecting rod bolts.
b. Tighten the connecting rod bolts.
c. Put a mark “1” on the connecting rod bolt

“2” and the connecting rod cap “3”.

d. Tighten the bolt further to reach the speci-

fied angle (150

e. After the installation, check that the section

shown “a” is flush with each other by touch-
ing the surface.

WARNING

EWA13990

• When the bolt is tightened more than the

specified angle, do not loosen the bolt
and then retighten it. Replace the bolt
with a new one and perform the proce-
dure again.

Connecting rod bolt

20 Nm (2.0 m·kg, 14 ft·lb)+150

a. Side machined face

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: [email protected]

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands

Yamaha YZF-R1 2007, Service Manual

Search results

Summary of Contents for YZF-R1 2007

Reviews:

Related manuals for YZF-R1 2007

Brands by name

Popular brands